Checking voltage supply and current consumption of fuel system pressurisation pump G6, engine codes CAYD, CAYE — AUDI

🧭 Before you start

Fits: VW Caddy III (2K, 2004–2015); platform code 2C0

• Special tools named: VAS 5565
• Renewed: fuel delivery unit

Don't miss

• Switch on ignition (2nd mechanic). The fuel pump must be heard to run for about 2 seconds.
• The fuel pump is now actuated for 30 seconds.
• Pickup clamp of hand-held multimeterV.A.G 1715 can also be connected to red terminal with lettering "“pickup clamp”" of test instrument adapter/DSO (5-pin)VAS 5565.

🔧 Engine codes this applies to

📋 Procedure

1. Raise vehicle.
2. Switch on ignition (2nd mechanic). The fuel pump must be heard to run for about 2 seconds.
3. Switch off ignition.
4. If fuel pump does not start, lower fuel tank .
5. Release connector (1) and pull it off flange.

6. Connect test instrument adapter/DSO (5-pin)VAS 5565 between connector and flange.
7. Connect hand-held multimeterV.A.G 1526D to contacts (1) and (5) of adapter.
8. Connect Vehicle diagnosis tester and then carry out Guided function "“Checking electrical fuel pump(s)”". [Note: The fuel pump is now actuated for 30 seconds.]
9. Read voltage value on hand-held multimeterV.A.G 1526D: specification = approx. battery voltage.
10. Check activation of fuel pump relay and wiring for open circuit and short circuit .
11. Remove fuel delivery unit .
12. Check that the electrical lines between flange and fuel pump are connected and have continuity.
13. Renew fuel delivery unit. [Note: The battery voltage and the diesel fuel temperature have a great influence on the current draw of the fuel pump. For this reason ensure that the battery voltage is at least 12 V whilst checking and the diesel fuel temperature does not fall to the freezing point.]
14. Lower fuel tank .
15. Release connector (1) and pull it off flange.
16. Connect test instrument adapter/DSO (5-pin)VAS 5565 to connector and fuel delivery unit.
17. Connect pick-up clamp (A) to red terminal with lettering "“pick-up clamp”" for test instrument adapter/DSO (5-pin)VAS 5565. [Note: Pickup clamp of hand-held multimeterV.A.G 1715 can also be connected to red terminal with lettering "“pickup clamp”" of test instrument adapter/DSO (5-pin)VAS 5565.]
18. Switch ignition on.
19. Connect Vehicle diagnosis tester and then carry out Guided function "“Checking electrical fuel pump(s)”". [Note: The fuel pump is now actuated for 30 seconds.]
20. Read current draw on hand-held multimeterV.A.G 1526D. Specification: max. 7.5 amps.
21. If the measured value is not within specifications:
22. Renew fuel delivery unit.

Other AUDI procedures

• Checking fuel filter
• Removing and installing fuel tank, front-wheel drive, engine codes CAYD, CAYE, CFHC, CFHE, CFHF, CLCA, CLCB, CFJA
• Removing and installing fuel delivery unit, front-wheel drive, engine codes CAYD, CAYE, CFHC, CFHE, CFHF, CLCA, CFJA
• Checking voltage supply and current consumption of fuel system pressurisation pump G6 engine codes BJB, BLS, BSU, BDJ, BST, BMM
• Emptying fuel tank, front-wheel drive, engine codes BJB, BLS, BSU, BDJ, BST, BMM
• Removing and installing toothed belt – Audi · 56 torque figures
• Removing engine – Audi A8 D3 · 41 torque figures
• Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
• Installing engine – Audi A8 D4 · 36 torque figures
• Removing and installing camshaft timing chain · 29 torque figures