SKODA / SEAT / VOLKSWAGEN CLCB — 2L Engine
2L · 140 hp
Engine overview
Vehicles with this engine
Torque figures by job
From the step-by-step procedures for this engine — each figure sits in the step that uses it.
- 50 Nm (37 lb-ft) — Tighten nut of assembly tool T10134 with torque wrench (5
- 8 Nm (5.9 lb-ft) — Tighten securing bolts (arrows) to
- 22 Nm (16 lb-ft) — Remove protective cap, fit oil supply line to turbocharger and tighten to
- 35 Nm (26 lb-ft) — Tighten hexagon nut of assembly tool T10134 to
- 15 Nm (11 lb-ft) — Tighten new securing bolts for sealing flange to
- 5 Nm (3.7 lb-ft) — Install engine speed sender G28(arrow) and tighten securing bolt to
- 60 Nm (44 lb-ft) — Install flywheel using new bolts
- 40 Nm (30 lb-ft) — Tighten hexagon nut of assembly tool T10134 to
- 45 Nm (33 lb-ft) — Tighten hexagon nut for assembly tool T10134 to
- 15 Nm (11 lb-ft) — Tighten securing bolts (3) using T-bar and 10 mm socket3185
- 10 Nm (7.4 lb-ft) — Screw on and tighten bolt (1)
- 200 Nm (148 lb-ft) — To tighten union nut (2), use torque wrench (40
- 40 Nm (30 lb-ft) — Tighten all bolts to
- 15 Nm (11 lb-ft) — Tighten securing bolts for sealing flange to
- 110 Nm (81 lb-ft) — Tighten locking ring using wrench T10202
- 10 Nm (7.4 lb-ft) — Secure accelerator module with bolt (3) and tighten to specified torque of
- 15 Nm (11 lb-ft) — Insert coolant pump (2) in cylinder block and tighten securing bolts (1) to
Engine codes in the same family
The same code prefix usually means the same block with a different output, fuel or model year. Procedures are often shared — check the code on the engine plate.
Workshop procedures for this engine
Step-by-step procedures from the workshop database, carrying 31 torque figures.
- Removing and installing sealing flange on gearbox side · 6 torque figures
- Removing and installing particulate filter · 3 torque figures
- Replacing vacuum unit with position sender for charge pressure positioner G581
- Installing high-pressure lines · 3 torque figures
- Installing a new balancer shaft module · 3 torque figures
- Removing and installing high-pressure lines · 1 torque figures
- Filling with incorrect fuel, engine codes CFHC, CFHE, CFHF, CLCA, CLCB, CFJA
- Installing 4/2-way valve with thermostat – VW 2.0 TDI · 2 torque figures
- Measuring radial clearance of conrods – VW Touareg II · 4 torque figures
- Checking exhaust gas recirculation cooler for leaks
- Installing a previously used balancer shaft module again · 3 torque figures
- Removing and installing vacuum pump – Audi A8 D3 · 2 torque figures
- Filling with incorrect fuel, engine codes CAYD, CAYE
- Renewing valve stem seals with cylinder head installed
- Removing and installing ancillary bracket – Audi 2.0 TDI · 1 torque figures
- Measuring radial clearance of camshafts – VW Touareg II · 3 torque figures
- Removing and installing left coolant pipe – VW Touareg I
- Renewing valve stem seals with cylinder head installed
- Renewing valve stem seals with cylinder head removed – VW CDLJ
- Renewing valve stem seals with cylinder head removed
- Removing and installing exhaust gas recirculation cooler
- Removing and installing fuel tank, four-wheel drive, engine codes CFHC, CFHE, CFHF, CLCA, CLCB, CFJA
- Checking return flow rate of injectors with engine running
- Emptying fuel tank, front-wheel drive, engine codes CAYD, CAYE, CFHC, CFHE, CFHF, CLCA, CLCB, CFJA
- Checking delivery pressure of fuel pump – VW
Got a CLCB problem? Ask for free.
Describe the symptoms — TorqFix replies with a diagnosis cited from verified workshop data.
Get free diagnosis →Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 14 Oct 2026.