Checking fuel filter — AUDI
Checking fuel filter on Audi: 19 steps, engines BDJ, BJB, BJJ, BJK. What to remove, in what order, and what to check after.
Workshop procedure for AUDI — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
Fits: VW Caddy III (2K, 2004–2015); platform code 2C0
- Special tools named: VAS 6551/3, VAS 6551/4
- Renewed: fuel filter
🔧 Engine codes this applies to
📋 Procedure
- ⚠ Read through the rules for cleanliness and the instructions for working on the fuel system .Always follow these rules for cleanliness and instructions before starting work and while working on the fuel system.Wrap a clean cloth around the connection before opening the fuel system, then carefully loosen the connection to release the pressure. — Remove fuel supply line (3) on fuel filter.
- Collect escaping fuel with a cleaning cloth.
- Attach connection (A) of pressure testerVAS 6551 with line VAS 6551/3 to open end of fuel filter.
- Attach connection (B) of pressure testerVAS 6551 together with line VAS 6551/4 to open line of high pressure pump.
- Switch on pressure testerVAS 6551 by pressing On/Off push button.
- Close shut-off tap (C) of pressure testerVAS 6551.
- Carefully open shut-off valves (A) and (B).
- Start engine.
- Connect fuel supply line (3) to fuel filter again.
- Remove fuel supply line (5) on fuel filter.
- Collect escaping fuel with a cleaning cloth.
- Attach connection (A) of pressure testerVAS 6551 with line VAS 6551/3 to open end of fuel filter.
- Attach connection (B) of pressure testerVAS 6551 to open line of fuel tank using line VAS 6551/4.
- Switch on pressure testerVAS 6551 by pressing On/Off push button.
- Close shut-off tap (C) of pressure testerVAS 6551.
- Carefully open shut-off valves (A) and (B).
- Start engine.
- Renew fuel filter.
- Check fuel system pressurisation pump G6.
Other AUDI procedures
- Removing and installing fuel delivery unit, four-wheel drive · 1 torque figures
- Removing and installing fuel tank, four-wheel drive, engine codes BJB, BLS, BSU
- Removing and installing fuel gauge senderG, front-wheel drive, engine codes CAYD, CAYE, CFHC, CFHE, CFHF, CLCA, CFJA
- Filling with incorrect fuel, engine codes CFHC, CFHE, CFHF, CLCA, CLCB, CFJA
- Renewing O-rings for unit injectors – Audi 2.0 TDI
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.