AUDI / VW CSLB — 2L Engine
2L · 113 hp
Engine overview
Torque figures by job
From the step-by-step procedures for this engine — each figure sits in the step that uses it.
- 15 Nm (11 lb-ft) — Diagonally tighten the new sealing flange bolts alternately to a torque of
- 6 Nm (4.4 lb-ft) — ⚠ Risk of damage to the securing thread of the delivery module
- 6 Nm (4.4 lb-ft) — To compensate for the settling, wait at least 2 minutes before tightening securing bolts…
- 50 Nm (37 lb-ft) — Tighten union nuts of all new injection lines using torque wrench (5
- 40 Nm (30 lb-ft) — Tighten all bolts to
- 5 Nm (3.7 lb-ft) — Start securing clamp bolt (3), and tighten it to
- 30 Nm (22 lb-ft) — Fit conrod bearing cap and tighten to
- 10 Nm (7.4 lb-ft) — Fit retaining frame and tighten to
- 15 Nm (11 lb-ft) — Tighten bolts (1 … 6) in diagonal sequence to
- 15 Nm (11 lb-ft) — Tighten bolts (7 … 10) to
Engine codes in the same family
The same code prefix usually means the same block with a different output, fuel or model year. Procedures are often shared — check the code on the engine plate.
Workshop procedures for this engine
Step-by-step procedures from the workshop database, carrying 15 torque figures.
- Removing and installing sealing flange on gearbox side · 6 torque figures
- Removing and installing high-pressure lines · 1 torque figures
- Removing engine, Crafter 4MOTION with Achleitner four-wheel drive
- Checking exhaust gas recirculation cooler for leaks
- Removing and installing turbocharger, single turbo
- Removing and installing pump for reducing agent V437 · 2 torque figures
- Removing and installing ancillary bracket · 1 torque figures
- Renewing valve stem seals with cylinder head removed
- Removing and installing turbocharger, Crafter 4MOTION with Achleitner four-wheel drive
- Assembly overview - sealing flange, belt pulley end · 2 torque figures
- Removing and installing engine control unit J623 with protective housing
- Checking hydraulic compensation elements
- Checking fuel filter
- Retrofitting auxiliary drive (genuine parts set)
- Removing and installing injector for reduction agent N474 · 1 torque figures
- Measuring radial play of camshaft · 1 torque figures
- Checking return flow rate of injectors at starter speed
- Removing and installing air filter housing
- Removing and installing coolant pipe with coolant hose
- Assembly overview - cylinder block, gearbox end · 1 torque figures
- Removing and installing oil supply line, single turbo
- Removing and installing tank for reduction agent
- Removing engine, Crafter 4MOTION with Achleitner four-wheel drive
- Removing and installing exhaust gas recirculation valve N18
- Removing and installing injector seals
Got a CSLB problem? Ask for free.
Describe the symptoms — TorqFix replies with a diagnosis cited from verified workshop data.
Get free diagnosis →Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 2 Oct 2026.