TorqFix

6-speed manual gearbox 02Q Volkswagen R GmbH — Renewing seal between gearbox and bevel box — VW

6-speed manual gearbox 02Q Volkswagen R GmbH — Renewing seal between gearbox and bevel box on VW: 13 steps, engines BYD, CDLA, CDLC, CDLF.

Workshop procedure for VW — the exact step sequence and torque figures, straight from real workshop data.

13 steps 5 engine codes

🧭 Before you start

Fits: VW Golf V / Jetta (1K, 2003–2009), VW Golf VI (5K, 2008–2013); platform code 137

🔧 Engine codes this applies to

BYDCDLACDLCCDLFCRZA

📐 80 workshop diagrams for BYD

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

6-speed manual gearbox 02Q Volkswagen R GmbH — Renewing seal between gearbox and bevel box — BYD · diagram 1
6-speed manual gearbox 02Q Volkswagen R GmbH — Renewing seal between gearbox and bevel box — BYD · diagram 2
6-speed manual gearbox 02Q Volkswagen R GmbH — Renewing seal between gearbox and bevel box — BYD · diagram 3
6-speed manual gearbox 02Q Volkswagen R GmbH — Renewing seal between gearbox and bevel box — BYD · diagram 4
6-speed manual gearbox 02Q Volkswagen R GmbH — Renewing seal between gearbox and bevel box — BYD · diagram 5
6-speed manual gearbox 02Q Volkswagen R GmbH — Renewing seal between gearbox and bevel box — BYD · diagram 6
6-speed manual gearbox 02Q Volkswagen R GmbH — Renewing seal between gearbox and bevel box — BYD · diagram 7
6-speed manual gearbox 02Q Volkswagen R GmbH — Renewing seal between gearbox and bevel box — BYD · diagram 8
+ 72 more diagrams
🔒 80 workshop diagrams for this job Ask about your VW BYD — free or sign up free to see the drawings

📋 Procedure

  1. Remove bevel box .
  2. Remove bevel box .
  3. Remove bevel box .
  4. Place drip trayV.A.G 1306 underneath.
  5. Lever bevel box oil seal out using extractor tool T20143/2 or oil seal extractor leverVW 681.
BYD? Steps differ between engine variants — check this job against your exact car before you commit to it. Check my car — free →
  1. Fill space between sealing lip and dust lip (arrow) with sealing greaseG 052 128 A1.
  2. Lightly oil outer circumference of new oil seal.
  3. Drive in seal to stop.
  4. Install bevel box .
  5. Install bevel box .
  6. Install bevel box .
  7. Check gear oil in bevel box .
  8. Check gear oil in gearbox .
Workshop diagrams

Ask TorqFix about your VW BYD — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.

Ask about your VW BYD — free → or sign up free to see the drawings

Other VW procedures

Who makes these pages, and how

TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.

The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.

Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.

Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com

The story behind TorqFix →

Workshop data on this page last updated 20 Sep 2026.