Clutch replacement: Citroen Nemo 1.2 (199A9000, F13DTE5)
Step-by-step clutch replacement for the Citroen Nemo 1.2 (199A9000/F13DTE5): 52 steps. What to remove, in what order, and what to check after.
Workshop procedure for CITROEN — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
- Renewed: if necessary note, oil seals
Don't miss
- We recommend that the clutch release bearing should always be renewed
- Always renew the concentric slave cylinder
- Do not bring any grease into contact with the clutch plate facing, clutch cover surface or flywheel surface
- Always renew the drive shaft seals
🔧 Engine codes this applies to
📐 63 workshop diagrams for 199A9000
Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.
📋 Procedure
Preparation and removal
- Clutch alignment tool:
- We recommend that the clutch release bearing should always be renewed
- Always renew the drive shaft seals
- Standard clutch mechanism
- Remove the gearbox
- Remove the bolts shown
- Remove the clutch cover bolts
- Remove the special tool
- Remove the clutch cover
- Remove the clutch plate
- Standard clutch mechanism
- Remove the gearbox
- Remove the clutch cover
- Remove the clutch plate
- Remove the clutch release bearing
Installation and checks
- Check the clutch release bearing guide tube and fork; renew if necessary
- Note: Always renew the concentric slave cylinder
- Check the clutch housing for leaks; check the crankshaft end seal thoroughly
- Check the flywheel friction surface for condition and wear
- Grease the thrust bearing inner bore, drive plate splines and release fork pivot points
- Note: Do not bring any grease into contact with the clutch plate facing, clutch cover surface or flywheel surface
- Renew the oil seals if necessary
- Clutch mechanism with automatic play adjustment
- Fit the clutch plate
- Fit the clutch alignment tool
- Fit the clutch cover
- Fit the special tools
- Compress the mechanism by turning the screw
- Refit the bolts
- Remove the special tools
- Tighten the clutch cover bolts
- Refit the clutch release bearing
- Refit the gearbox
- Fit the clutch plate
- Fit the clutch alignment tool
- Fit the clutch cover
- Check the marks on the clutch cover and the flywheel
- Tighten the bolts in several stages, in a criss-cross pattern
- Fit the special tool
- Compress the mechanism by turning the screw
- Refit the gearbox
Ask TorqFix about your Citroen 199A9000 — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.
Ask about your Citroen 199A9000 — free → or sign up free to see the drawingsOther CITROEN procedures
- Citroen Nemo MTM 1.2 199A9000 gearbox removal & installation
- Peugeot Bipper, ; 208 clutch replacement
- Peugeot Bipper F13DTE5 timing chain replacement
- Citroen DW10TD timing belt replacement
- Citroen DW10TD timing belt replacement
- Citroen Xantia non turbo 1.9 HDi XUD9A timing belt replacement
- Citroen Xantia turbo timing belt replacement
- Citroen EW10J4/EW7J4 timing belt replacement
- Citroen C4 MCP DV6TED4 gearbox removal & installation
- Citroen 1997 timing belt replacement
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix → · How these pages are made →Workshop data on this page last updated 20 Sep 2026.