C5(X7) - DV6TED4 — CITROEN
C5(X7) - DV6TED4 on Citroen: 67 steps, engines DV6TED4(9HZ). What to remove, in what order, and what to check after.
Workshop procedure for CITROEN — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
Fits: platform codes 1.6, HDI, 16V, FAP
Don't miss
- Caution! The temperature of the engine and exhaust will increase significantly
- Caution! Note the additive hazard warnings
🔧 Engine codes this applies to
📐 27 workshop diagrams for DV6TED4(9HZ)
Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.
📋 Procedure
Preparation and removal
- Caution! The temperature of the engine and exhaust will increase significantly
- Check the tightness of the turbocharger hoses
- Note: The fuel tank should contain at least 20 litres of fuel
- Select the highest suspension position
- Remove the underbody cover
- Disconnect the line(s)
- Connect the diagnostic tool
- Disconnect the pipe
- Delete all the fault codes
- Activate the diesel particulate filter regeneration function
- Caution! Note the additive hazard warnings
- Detach the breather pipe
- Note: Mark the position
- Release the clip(s)
- Remove the additive tank
- Disconnect the filler pipe
- Run the engine at idle speed
- Wait until the engine has cooled down
- Stop the engine
- Empty the additive tank
- Collect the escaping fluid in a measuring container
- Check the additive level
Installation and checks
- Refit the additive tank
- Installation is in the reverse order of removal
- Raise the vehicle
- Remove the underbody cover
- Refill the additive tank
- Refit the cover
- Reprogram the additive pump
- Use the diagnostic tool
- Raise the filling container above the additive tank
- Open the filling container valve
- Close the valve when fluid is escaping through the overflow pipe
- Disconnect the additive tank filling kit filler pipe from the additive tank filler pipe
- Disconnect the overflow pipe
- Remove the filling and overflow container
- Reconnect the filler pipe
- Using the diagnostic tool:
- Check the additive level
- Refit the cover
- Lower the vehicle
- Reset the additive system
- Use the diagnostic tool
Ask TorqFix about your Citroen DV6TED4(9HZ) — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.
Ask about your Citroen DV6TED4(9HZ) — free → or sign up free to see the drawingsOther CITROEN procedures
- Citroen Xsara Picasso: DV6TED4 DPF removal
- Peugeot 5008 DV6TED4 DPF removal
- 207 - DV6TED4
- 206, 307 - DV6TED4: Additive refill
- Peugeot 207 BE4R DV6DTED gearbox removal & installation
- Citroen DW10TD timing belt replacement
- Citroen DW10TD timing belt replacement
- Citroen Xantia non turbo 1.9 HDi XUD9A timing belt replacement
- Citroen Xantia turbo timing belt replacement
- Citroen EW10J4/EW7J4 timing belt replacement
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.