TorqFix

C2 - DV6TED4 — CITROEN

C2 - DV6TED4 on Citroen: 71 steps, engines DV6TED4(9HZ), TU5JP4S(NFS). What to remove, in what order, and what to check after.

Workshop procedure for CITROEN — the exact step sequence and torque figures, straight from real workshop data.

71 steps 2 engine codes

🧭 Before you start

Fits: platform codes 1.6, 16V, VTS, |, HDIF

Don't miss

  • Caution! Do not damage the flexible pipe
  • Do not re-use the drained fluid or fluid from opened containers
  • The flexible reservoir must fit flush with the additive tank housing

🔧 Engine codes this applies to

📐 27 workshop diagrams for DV6TED4(9HZ)

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

C2 - DV6TED4 — DV6TED4(9HZ) · diagram 1
C2 - DV6TED4 — DV6TED4(9HZ) · diagram 2
C2 - DV6TED4 — DV6TED4(9HZ) · diagram 3
C2 - DV6TED4 — DV6TED4(9HZ) · diagram 4
C2 - DV6TED4 — DV6TED4(9HZ) · diagram 5
C2 - DV6TED4 — DV6TED4(9HZ) · diagram 6
C2 - DV6TED4 — DV6TED4(9HZ) · diagram 7
C2 - DV6TED4 — DV6TED4(9HZ) · diagram 8
+ 19 more diagrams

📋 Procedure

Preparation and removal

  1. Note: Do not re-use the drained fluid or fluid from opened containers
  2. Raise the vehicle
  3. Remove the spacer
  4. Start the engine
  5. If equipped:
DV6TED4(9HZ)? Steps differ between engine variants — check this job against your exact car before you commit to it. Check my car — free →
  1. Disconnect the air-conditioning compressor and place it aside
  2. Remove the bolts shown
  3. Disconnect the pipe(s)
  4. Activate the diesel particulate filter regeneration function
  5. Follow the instructions on the screen of the diagnostic tool
  6. Move the heat shield
  7. Caution! Do not damage the flexible pipe
  8. Disconnect the battery
  9. Wait until the engine has cooled down

Installation and checks

  1. Tighten the clamp(s)
  2. Check the exhaust system for leaks and damage
  3. Refit the additive reservoir
  4. Fit a new clip
  5. Note: The flexible reservoir must fit flush with the additive tank housing
  6. Refit the additive tank
  7. Installation is in the reverse order of removal
  8. Reset the additive system
  9. Stop the engine
Workshop diagrams

Ask TorqFix about your Citroen DV6TED4(9HZ) — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.

Ask about your Citroen DV6TED4(9HZ) — free → or sign up free to see the drawings

Who makes these pages, and how

TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.

The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.

Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.

Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com

The story behind TorqFix →

Workshop data on this page last updated 20 Sep 2026.