Wire routing, connectors, connections and retainer on valve body — VW
Wire routing, connectors, connections and retainer on valve body on VW: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for VW — the factory write-up, straight from real workshop data.
📋 Procedure
Wire routing, connectors, connections and retainer on valve body
This chapter contains information and figures pertaining to work on the valve body.
Vehicles with a 2nd generation gearbox (such as gearbox codes
“MAN”
or
“PDW”
)
Vehicles with a 3rd generation gearbox (such as gearbox code
“NTJ”
)
Wire routing, connectors and connections - vehicles with a 2nd generation gearbox
Anchor
Note
This chapter contains information and figures pertaining to work on the valve body.
Before separating connectors at senders and solenoid valves, solenoid valve or sender and respective connector must be identified.
1
Solenoid valve 4
N91
2
Solenoid valve 6
N93
3
Solenoid valve 5
N92
4
Solenoid valve 9
N282
5
Solenoid valve 10
N283
6
Solenoid valve 3
N90
7
Solenoid valve 1
N88
8
Solenoid valve 2
N89
A
Connection for
gearbox output speed sender
G195
B
Connection for
gearbox input speed sender
G182
Retainer for connectors, fixing wires in place
Note
The
arrows
in the illustration point to wire brackets or retainers.
Retainer for connection
gearbox output speed sender
G195
Specified tightening torque
Chapter
Retainer for connection
gearbox input speed sender
G182
Specified tightening torque
Chapter
Gearbox oil temperature sender
G93
Selector lever
Wire routing, connectors and connections - vehicles with a 3rd generation gearbox
Anchor
Note
This chapter contains information and figures pertaining to work on the valve body.
Before separating connectors at senders and solenoid valves, solenoid valve or sender and respective connector must be identified.
1
Solenoid valve 1
N88
2
Solenoid valve 2
N89
3
Pressure control valve 5 for automatic gearbox
N233
4
Pressure control valve 7 for automatic gearbox
N443
5
Pressure control valve 1 for automatic gearbox
N215
6
Pressure control valve 4 for automatic gearbox
N218
7
Pressure control valve 3 for automatic gearbox
N217
8
Pressure control valve 2 for automatic gearbox
N216
A
Gearbox oil temperature sender
G93
B
Connection for
gearbox output speed sender
G182
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other VW procedures
- Removing engine · 41 torque figures
- Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
- Adjusting valve timing – VW Passat B5 · 83 torque figures
- Removing and installing camshafts – VW Passat B6 · 39 torque figures
- Removing and installing coolant pump · 53 torque figures
- Renewing seals on injectors – VW Jetta VI · 2 torque figures
- Removing and installing circulation pump V55 – VW · 3 torque figures
- Removing and installing front fuel tanks, natural gas, engine code BSX
- Renewing oil seal for right flange shaft, four-wheel drive · 2 torque figures
- Removing gearbox; Golf Cabriolet 2012 ► 1,4 l - 92 and 110 kW petrol engine, engine lifting eyes »at front« of engine
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.