Assembly overview - rear axle, vehicles with twin wheels — VW
Assembly overview - rear axle, vehicles with twin wheels on VW: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for VW — the factory write-up, straight from real workshop data.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
Assembly overview - rear axle, vehicles with twin wheels
WARNING
It is not permitted to carry out welding and straightening operations on load-bearing or wheel-guiding suspension components.
Always renew self-locking nuts and bolts.
Always renew corroded nuts and bolts.
Caution
Bonded rubber bushes can be twisted only to a limited extent. Therefore, tighten the bolted connections of components with bonded rubber bushes only when the axle beam is raised or when the vehicle is standing on its wheels (in the unladen position)
Chapter
.
Bump stop
Allocation
Electronic Parts Catalogue
.
Note
The stop buffer for the Crafter 4MOTION with Achleitner four-wheel drive is bigger in size, but the removal and installation procedure is identical.
Removing and installing
Chapter
U bolt
Allocation
Electronic Parts Catalogue
.
Note
The U bolt for the Crafter 4MOTION with Achleitner four-wheel drive is bigger in size, but the removal and installation procedure is identical.
Nut
Always renew after removing
M12 × 1.5: 90 Nm
M16 × 1.5: 185 Nm
Shackle
Removing and installing
Chapter
Rubber bush for shackle
Renewing
Chapter
.
Bolt
Always renew after removing
Nut
Always renew after removing
M12 × 1.5: 85 Nm
M16 × 1.5: 185 Nm
Bolt
Always renew after removing
Rubber bush for leaf spring
Renewing
Chapter
.
Leaf spring
Allocation
Electronic Parts Catalogue
.
Removing and installing
Chapter
Saddle plate
Allocation
Electronic Parts Catalogue
.
Nut
Always renew after removing
106 Nm
Coupling rod
Allocation
Electronic Parts Catalogue
Note
The coupling rods must have the same length on both sides.
Removing and installing
Chapter
Removing and installing, Crafter 4MOTION with Achleitner four-wheel drive
Chapter
.
Bolt
Always renew after removing
M10 × 1.5: 60 Nm
M12 × 1.5: 120 Nm
Bolt
Always renew after removing
Clamp
Anti-roll bar
Removing and installing
Chapter
Rubber mounting
Nut
Always renew after removing
160 Nm
Bolt
Always renew after removing
Nut
Always renew after removing
M12 × 1.5: 106 Nm
M14 × 1.5: 135 Nm
Shock absorber
Allocation
Electronic Parts Catalogue
.
Removing and installing
Chapter
.
Bolt
Always renew after removing
M14 × 1.5 × 110: 106 Nm
M14 × 1.5 × 160: 135 Nm
Propshaft
Before removing, mark position relative to final drive flange.
Removing and installing
Rep. gr.
39
propshaft
Rear axle
Removing and installing
Rep. gr.
39
rear axle
Removing and installing final drive
Rep. gr.
39
Final drive
Bolt
Always renew after removing
Nut
Always renew after removing
185 Nm
Damper weight
Pressed onto leaf spring
Not available as replacement part
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other VW procedures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.