TorqFix

Gearbox removal & installation: Peugeot 206 motor en bak (EW10J4)

Step-by-step gearbox removal & installation for the Peugeot 206 motor en bak (EW10J4): 33 steps. What to remove, in what order, and what to check after.

Workshop procedure for PEUGEOT — the exact step sequence and torque figures, straight from real workshop data.

33 steps 2 engine codes

🧭 Before you start

  • Opens: gearbox oil

Don't miss

  • Remove the air-conditioning compressor but do not disconnect
  • Remove the power steering pump but do not disconnect the lines

🔧 Engine codes this applies to

EW10J4(RFN)EW10J4(RFR)

📐 40 workshop diagrams for EW10J4(RFN)

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

206 EW10J4 motor en bak uit in — EW10J4(RFN) · diagram 1
206 EW10J4 motor en bak uit in — EW10J4(RFN) · diagram 2
206 EW10J4 motor en bak uit in — EW10J4(RFN) · diagram 3
206 EW10J4 motor en bak uit in — EW10J4(RFN) · diagram 4
206 EW10J4 motor en bak uit in — EW10J4(RFN) · diagram 5
206 EW10J4 motor en bak uit in — EW10J4(RFN) · diagram 6
206 EW10J4 motor en bak uit in — EW10J4(RFN) · diagram 7
206 EW10J4 motor en bak uit in — EW10J4(RFN) · diagram 8
+ 32 more diagrams
🔒 40 workshop diagrams for this job Ask about your Peugeot EW10J4(RFN) — free or sign up free to see the drawings

📋 Procedure

  1. Engine supports:
  2. The engine and gearbox are removed as a unit
  3. Drain the gearbox oil
  4. Remove the drive shafts
  5. Remove the torque rod
EW10J4(RFN)? Steps differ between engine variants — check this job against your exact car before you commit to it. Check my car — free →
  1. Remove the power steering pump line supports
  2. Disconnect the gear-shift control
  3. Disconnect the exhaust pipe from the manifold
  4. Vehicles with air conditioning:
  5. Disconnect the air-conditioning compressor electrical connections
  6. Remove the air-conditioning compressor but do not disconnect
  7. Disconnect as shown:
  8. Disconnect the clutch cable
  9. Disconnect the radiator hoses
  10. Remove the air filter
  11. Remove the air duct
  12. Remove the radiator
  13. Remove the power steering pump but do not disconnect the lines
  14. Remove the bolt
  15. Remove the power steering line mounts
  16. Release the fuel pressure
  17. Disconnect the hose
  18. Disconnect the fuel feed line
  19. Disconnect the engine wiring loom
  20. Remove the alternator
  21. Disconnect the oil pressure sensor
  22. Remove the engine supports
  23. Remove the engine/gearbox
Workshop diagrams

Ask TorqFix about your Peugeot EW10J4(RFN) — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.

Ask about your Peugeot EW10J4(RFN) — free → or sign up free to see the drawings

Other PEUGEOT procedures

Who makes these pages, and how

TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.

The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.

Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.

Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com

The story behind TorqFix → · How these pages are made →

Workshop data on this page last updated 20 Sep 2026.