Removing engine - vehicles with engine codes CGQB, CVUB, CVUC, DEHA — AUDI

🧭 Before you start

Fits: Audi Q5 (8R, 2008–2017)

• Opens: refrigerant (A/C)
• Special tools named: VAS 6131/11, VAS 6131/13, VAS 6131/10, 5 mm ring spanner

Don't miss

• Carefully pull engine cover panel off retaining pins one after the other (arrows). Do not jerk engine cover panel away, and do not try to pull on one side only.
• Collect drained coolant in a clean container for disposal.
• Disregard (item 2).
• Danger of damage to refrigerant lines and hoses.Do NOT stretch, kink or bend refrigerant lines and hoses. — Remove bolt (2), disconnect refrigerant line from air conditioner compressor and move to one side.
• Disregard (items 1, 3).

🔧 Engine codes this applies to

🔩 Torque settings

Values can differ between engine variants — check the code stamped on your block.

ℹ️ Always cross-check the exact figure against your vehicle's factory manual before final tightening — a wrong torque can damage the engine. These values are extracted from workshop data and may not cover every variant or revision.

📐 1 workshop diagram for CDUD

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

📋 Procedure

1. ⚠ Make sure the vehicle cannot tip over when the engine is removed.Secure the vehicle, to do so, the luggage compartment must be empty.The fuel system operates at extremely high pressure. This can cause injury.The fuel pressure in the high-pressure section of the injection system must be reduced to a residual pressure prior to opening the system. — Set front wheels to straight-ahead position.
2. ⚠ Electronic components are susceptible to damage.Observe notes on procedure for disconnecting the battery. — Switch off ignition and take out ignition key.
3. Disconnect earth wire (arrow) from battery terminal Electrical system27Battery, Disconnecting and connecting battery.
4. Discharge refrigerant circuit Heating, air conditioning87Refrigerant circuit.
5. Remove lock carrier cover (3)General body repairs, exterior50Lock carrier.

6. Carefully pull engine cover panel off retaining pins one after the other (arrows). Do not jerk engine cover panel away, and do not try to pull on one side only.
7. ⚠ Hot steam/hot coolant can escape - risk of scalding.The cooling system is under pressure when the engine is hot.To allow pressure to dissipate, cover filler cap on coolant expansion tank with cloth and open carefully. — Open filler cap on coolant expansion tank.
8. Remove both front wheels.
9. Remove wheel housing liners (1) (front left and front right) General body repairs, exterior66Wheel housing liners; Exploded view - wheel housing liner (front).
10. Remove noise insulation (1) and (2)General body repairs, exterior66Noise insulation; Exploded view - noise insulation. [Note: Collect drained coolant in a clean container for disposal.]
11. Place drip tray for workshop hoistVAS 6208 beneath engine.
12. Remove drain plug (2) and drain off coolant.
13. Lift retaining clip (1) and disconnect coolant hose from radiator (bottom right).
14. Release hose clip (arrow), disconnect coolant hose from coolant pipe (front left) and drain off coolant.
15. Lift retaining clip (arrow), disconnect coolant hose (rear right) and drain off coolant.
16. Unplug electrical connector (1) on charge pressure sender G31/intake air temperature sender G42 and move clear electrical wiring. [Note: Disregard (item 2).]
17. Unscrew nut (arrow) on longitudinal member (right-side) and move earth cables clear.
18. Unplug electrical connectors (1, 2) for radiator fan (push retainer to the rear (arrow) and press down release catch).
19. Move electrical wiring harness clear.
20. Unscrew bolts (arrows) and press stop (1) for torque reaction support towards engine.
21. Release hose clip (arrow), disconnect air hose from air pipe and move to one side.
22. Remove bolt (1) and nut (3) on both sides and detach strut (2) for lock carrier.
23. Remove bolts (arrows).
24. Detach air duct (1) with intermediate flange (2) from air cleaner housing.
25. Unplug electrical connector (1) from air mass meter G70.
26. Remove air hose and air mass meter G70. To do so, release hose clip (2) and clamps (arrows).
27. Disconnect vacuum line (1).
28. Detach air cleaner housing, unplug electrical connector (2) at air filter bypass flap valve N275 on reverse side of air cleaner and move electrical wiring clear.
29. ⚠ Take care to keep components clean.Observe rules for cleanliness when working on the fuel supply system . — Release hose clips and detach fuel hoses:
30. Release hose clip (arrow) and disconnect coolant hose from coolant pipe (front).
31. Release hose clip (arrow) and detach air hose.
32. Disconnect vacuum hose (arrow).
33. ⚠ Danger of damage to refrigerant lines and hoses.Do NOT stretch, kink or bend refrigerant lines and hoses. — Remove bolt (2), disconnect refrigerant line from air conditioner compressor and move to one side.
34. Seal off open lines and connections with clean plugs from engine bung setVAS 6122. [Note: Disregard (items 1, 3).]
35. Disconnect coolant hose (3) from coolant expansion tank (pull out retaining clip). [Note: Disregard items marked (1, 2) and (arrows).]
36. Remove plenum chamber cover (2)General body repairs, exterior50Bulkhead; Removing and installing plenum chamber cover.
37. Unplug electrical connector (1) and move wiring clear.
38. Unscrew nuts (arrows), move control unit for NOx sender J583(item 2) clear and place it on engine.
39. Open cover (3).
40. Remove nuts (1 and 2), detach electrical wiring and move wiring clear.
41. Unplug electrical connectors (arrows) from catalytic converter heater control unit 1J1021 and move electrical wiring harness clear.
42. Release retainer (arrow A) and open cover (arrow B).
43. Remove nuts (1 ... 4) for electrical wiring.
44. Detach electrical connector (5) from bracket and unplug.
45. Unscrew bolt (6) and remove terminal 30 wiring junction 2TV22.
46. Remove bolts (1) and nuts (2) and (arrow) and detach body brace.
47. Unplug electrical connector at brake servo pressure sensor G294(arrow).
48. Lift off foam plastic block (1). [Note: Disregard (item 2).]
49. Working from wheel housing, release catches using a 5.5 mm ring spanner (item 1) and remove wiring protector (2) from above.
50. Release wiring harness (3) leading to alternator and starter using removal lever80 - 200 and move clear.
51. Release catch (arrow) to open wiring duct (1) and move wiring harness clear.
52. Lift retaining clip (3) and disconnect coolant hose.
53. Disconnect vacuum hose (2) on rear side of plenum chamber partition panel in direction of (arrow) and detach vacuum connection (1) from plenum chamber partition panel.
54. Detach refrigerant lines (A, C) from refrigerant line with inner heat exchanger (B)Heating, air conditioning87Overview of fitting locations - air conditioner; Overview of fitting locations - components not located in passenger compartment.
55. Remove nut (3) and bolt (2).
56. Pull filler neck (1) with filler pipe out of washer fluid reservoir and through opening in body (arrow).
57. Remove bolts (1, 2, 4) and detach cover (3) for electronics box in engine compartment (arrow).
58. Remove nut (5) and move earth wire clear.
59. Release catches (arrows A) and take out engine control unit (arrow B).
60. If fitted, unplug electrical connector (2).

Other AUDI procedures

• Removing and installing front exhaust pipe - vehicles with four-wheel drive
• Bleeding fuel supply line leading to metering pump, vehicles with auxiliary heater
• Removing and installing injector for reducing agent N474 - vehicles with engine codes CTBA and CTBC
• Removing and installing fuel pump control unit J538
• Exploded view - camshaft timing chains
• Removing and installing toothed belt – Audi · 56 torque figures
• Removing engine – Audi A8 D3 · 41 torque figures
• Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
• Installing engine – Audi A8 D4 · 36 torque figures
• Removing and installing camshaft timing chain · 29 torque figures