Removing and installing engine bracket, Passat, Eos and CC — VW

🧭 Before you start

Fits: VW Passat B7 saloon (362, 2010–2014), VW Passat B7 Variant (365, 2010–2014), VW Passat CC (357, 2008–2012); platform code 1F8

Don't miss

• The assembly mounting may only be removed if the engine is supported with support bracket 10-222A!The engine bracket must be loosened only when the assembly mounting has been removed.
• The securing bolt (1) is accessible through an aperture in the wheel housing. Raise and lower the engine via the spindle of the support bracket10 - 222 A, if necessary, to remove or fit bolts (2) and (3).
• When raising and lowering engine using support bracket10-222A, ensure that no components or hoses are damaged, overstretched or torn off. — Unscrew securing bolts of engine bracket in sequence (3…1).

🔧 Engine codes this applies to

📋 Procedure

1. Remove engine cover .
2. Remove intake line between air mass meter G70 and turbocharger.
3. Remove supplementary fuel pump V393 or fuel pump 2V27720Fuel pump: Removing and installing fuel pump.
4. Unplug connector at pressure differential sender G505(2), unscrew securing bolt (1).
5. Unclip lines for pressure differential sender G505 out of upper toothed belt guard together with bracket (1).

6. Lay pressure differential sender G505 on particulate filter together with bracket.
7. Support engine in its installation position . [Note: The assembly mounting may only be removed if the engine is supported with support bracket 10-222A!The engine bracket must be loosened only when the assembly mounting has been removed.]
8. Unscrew bolts (B) and (C).
9. Unscrew bolts (A) and remove assembly mounting.
10. Unscrew coolant line securing bolt (arrow).
11. Remove front right wheel housing liner: General body repairs, exterior66Wheel housing liner; Removing and installing wheel housing liner.
12. Unscrew bottom coolant line securing bolt (arrow). [Note: The securing bolt (1) is accessible through an aperture in the wheel housing. Raise and lower the engine via the spindle of the support bracket10 - 222 A, if necessary, to remove or fit bolts (2) and (3).]
13. ⚠ When raising and lowering engine using support bracket10-222A, ensure that no components or hoses are damaged, overstretched or torn off. — Unscrew securing bolts of engine bracket in sequence (3…1).
14. Remove engine bracket upwards.
15. ⚠ The tightening sequence and specified torques for the engine bracket securing bolts must always be followed. Otherwise the engine bracket can be stressed, causing it to break. — Install engine bracket from above. [Note: The securing bolt (1) is accessible through an aperture in the wheel housing. Raise and lower the engine via the spindle of the support bracket10 - 222 A, if necessary, to remove or fit bolts (2) and (3).]
16. Initially screw in new securing bolts finger-tight in the sequence (1...3).
17. Tighten mounting bolts to the prescribed torque in the specified sequence .
18. Fit assembly mounting and tighten bolts (A) first and then (C). Specified torque
19. Move engine bracket into contact with assembly mounting.
20. Start bolts (B) and tighten them. Specified torque

Other VW procedures

• Filling and bleeding fuel system
• Checking supply line, vacuum reservoir and non-return valve
• Removing and installing air mass meter G70 – VW Jetta VI
• Filling and bleeding fuel system – VW Jetta VI 2.0 TDI
• Removing and installing engine control unit J623 with protective housing, Tiguan
• Removing engine · 41 torque figures
• Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
• Adjusting valve timing – VW Passat B5 · 83 torque figures
• Removing and installing camshafts – VW Passat B6 · 39 torque figures
• Removing and installing coolant pump · 53 torque figures