Assembly overview, pedal cluster with clutch position sender G476 - Touran from 06.03, Passat, Eos, Scirocco, Golf, and Golf Plus — VW
Assembly overview, pedal cluster with clutch position sender G476 - Touran from 06.03, Passat, Eos, Scirocco, Golf, and Golf Plus on VW: factory workshop.
Workshop procedure for VW — the factory write-up, straight from real workshop data.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
Assembly overview, pedal cluster with
clutch position sender
G476
- Touran from 06.03, Passat, Eos, Scirocco, Golf, and Golf Plus
Bulkhead
With support for mounting bracket
Seal
Always renew
Between mounting bracket and bulkhead
Self-adhesive
Bond to mounting bracket
Mounting bracket
For mounting clutch pedal
Is provided with damping in some equipment variants
Fig.
Removing and installing, Touran
Chapter
Removing and installing, Golf 2004 ►
Chapter
Removing and installing, Golf 2009 ► left-hand drive and Scirocco
Chapter
Removing and installing, Golf 2009 ► right-hand drive and Golf Plus right-hand drive
Chapter
Removing and installing, Golf Plus left-hand drive
Chapter
Removing and installing, Passat
Chapter
Removing and installing, Eos
Chapter
Bolt
Over-centre spring
Removing and installing, Touran from 06.03
Chapter
Removing and installing, Golf 2004 ►
Chapter
Removing and installing, Golf 2009 ► left-hand drive and Scirocco
Chapter
Removing and installing, Golf 2009 ► right-hand drive
Chapter
Removing and installing, Golf Plus
Chapter
Removing and installing, Passat
Chapter
Removing and installing, Eos
Chapter
Bearing bush
Pivot pin
Clutch pedal
Removing and installing, Touran
Chapter
Removing and installing, Golf 2004 ►
Chapter
Removing and installing, Golf 2009 ► left-hand drive and Scirocco
Chapter
Removing and installing, Golf 2009 ► right-hand drive
Chapter
Removing and installing, Golf Plus
Chapter
Removing and installing, Passat
Chapter
Removing and installing, Eos
Chapter
Support
To remove and install, separate master cylinder from clutch pedal (⇒ Removing and installing clutch pedal)
Touran
Chapter
Golf 2004 ►
Chapter
Golf 2009 ► left-hand drive and Scirocco
Chapter
Golf 2009 ► right-hand drive
Chapter
Golf Plus
Chapter
Passat
Chapter
Eos
Chapter
Seal
Always renew
Between master cylinder and mounting bracket
Master cylinder
Touran with
clutch position sender
G476
(from 06.03), removing and installing after removal of mounting bracket
Chapter
Passat, Eos, Scirocco, Golf, and Golf Plus, removing and installing after removal of mounting bracket
Chapter
Clutch position sender
G476
Allocation
Electronic parts catalogue
Removing and installing, Touran from 06.03, Passat, Eos, Scirocco, Golf and Golf Plus
Chapter
Can be checked in
“guided fault finding”
of
vehicle diagnosis, testing and information system
VAS 5051
The
clutch position sender
G476
is identified as
clutch pedal switch
F36
in
“guided fault finding”
Clip
Pull out clip to stop to remove and install pipe/hose line
Supply hose
Rubber
From 12. 05, plastic
Fig.
Golf 2009 ►, Golf Plus 2009 ► and Scirocco made from plastic
Fig.
Self-locking hexagon nut, 25 Nm
Qty. 3
For mounting bracket to bulkhead
Always renew
Hexagon nut, 25 Nm
Always renew
Stop
For clutch pedal
Mounting bracket with damping
arrows
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other VW procedures
- Removing engine · 41 torque figures
- Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
- Adjusting valve timing – VW Passat B5 · 83 torque figures
- Removing and installing camshafts – VW Passat B6 · 39 torque figures
- Removing and installing coolant pump · 53 torque figures
- Removing and installing bleeder – VW 2.0
- Removing and installing rear treble loudspeakers R14/R16 – VW · 1 torque figures
- Renewing needle bearing (polygon bearing) for stub shaft – VW
- Removing and installing fuel pump control unit J538
- Removing and installing upper toothed belt guard, vehicles without SCR system
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.