Removing and installing C-pillar trim, 2-door models: VW Polo 6C
Step-by-step removing and installing C-pillar trim, 2-door models for the VW Polo 6C: 14 steps, 2 torque figures.
Workshop procedure for VW — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
Fits: VW Polo 6C (2014–2017)
- Renewed: if necessary
Don't miss
- Before installing, check retaining clips for damage and renew if necessary.Ensure seat belt is positioned correctly.
- Ensure that trim is positioned in beading of rear lid seal.
🔩 Torque settings
Values can differ between engine variants — check the code stamped on your block.
| Torque | Fastener / step |
|---|---|
| 1.5 Nm (1.1 lb-ft) | Unscrew 2 bolts (1) and (2 |
| 40 Nm (30 lb-ft) | Remove bolt (1 |
ℹ️ Always cross-check the exact figure against your vehicle's factory manual before final tightening — a wrong torque can damage the engine. These values are extracted from workshop data and may not cover every variant or revision.
📋 Procedure
- Remove bench seat .
- Remove backrest .
- Release sill panel moulding from fasteners in sill at transition to side panel.
- Remove side trim panel .
- Remove roof end strip .
- Unscrew 2 bolts (1) and (2) (1.5 Nm) for luggage compartment cover which are located behind C-pillar trim. — 1.5 Nm (1.1 lb-ft)
- Unclip side of luggage compartment cover in upper area.
- Unclip C-pillar trim (1) in lower, rear area (arrow).
- Unclip C-pillar trim in lower, front area.
- Unclip C-pillar trim in upper area.
- Remove bolt (1) (40 Nm) and remove belt end anchor (2) from body. — 40 Nm (30 lb-ft)
- Thread seat belt through opening in C-pillar trim.
- Install in reverse order of removal. [Note: Before installing, check retaining clips for damage and renew if necessary.Ensure seat belt is positioned correctly.]
- Ensure that trim is positioned in beading of rear lid seal.
Other VW procedures
- Removing engine · 41 torque figures
- Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
- Adjusting valve timing – VW Passat B5 · 83 torque figures
- Removing and installing camshafts – VW Passat B6 · 39 torque figures
- Removing and installing coolant pump · 53 torque figures
- Removing and installing left flange shaft – VW Phaeton
- Removing and installing alternator, 1.9 l TDI engine with DSG
- Removing and installing starter, vehicles with 4.9 l, 230 kW TDI engine, automatic gearbox AL750-6A
- Removing and installing relay carrier in front right footwell · 1 torque figures
- Removing and installing alternator, 1.4 l 55 kW injection engine
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.