Adjusting assembly mountings (Golf, Eos, Scirocco) — VW
Adjusting assembly mountings (Golf, Eos, Scirocco) on VW: 14 steps, engines BZB, CAWA, CAWB, CBFA. What to remove, in what order, and what to check after.
Workshop procedure for VW — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
Fits: VW Golf V / Jetta (1K, 2003–2009), VW Golf VI (5K, 2008–2013); platform codes 1F7, 137
Don't miss
- Support engine with gearbox, but do not raise.
📐 74 workshop diagrams for BZB
Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.
📋 Procedure
- Remove engine cover panel .
- Remove air filter .
- If fitted, remove charge air duct to sound generator .
- ⚠ To prevent damage to the electronic components when disconnecting the battery:Observe notes on procedure for disconnecting the battery. — With ignition switched off, disconnect battery earth cable (arrow).
- Remove battery 27.
- Remove battery tray (arrows).
- Fit support bracket10 - 222 A with the following tool parts: [Note: The racks10 - 222 A /1 must not be located on the screw plates of the wings, as this will otherwise cause damage to them.The shackle10 - 222 A /12 is needed so the engine is raised in its installation position and does not »fall back«.]
- Support engine with gearbox, but do not raise.
- Renew assembly mounting bolts (arrows) on engine side one after the other (if not already carried out during engine installation) and screw in hand-tight.
- Renew assembly mounting bolts (arrows) on gearbox side one after the other (if not already carried out during engine installation) and screw in hand-tight.
- Renew assembly mounting bolts (arrows) on gearbox side one after the other (if not already carried out during engine installation) and screw in hand-tight.
- Slacken bolts on left and right-hand support arms by about two turns each.
- Adjust assembly mounting and screw in securing bolts hand-tight.
- Tighten bolts for assembly mounting to required specified torque .
Ask TorqFix about your VW BZB — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.
Ask about your VW BZB — free → or sign up free to see the drawingsOther VW procedures
- Removing and installing radiator fan V7 and radiator fan 2V177
- Removing and installing fuel gauge sender G – VW
- Assembly overview - sealing flange on gearbox side and dual-mass flywheel/drive plate · 1 torque figures
- Renewing Teflon seal on injector
- Removing and installing small coolant pipe – VW Jetta VI
- Removing engine · 41 torque figures
- Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
- Adjusting valve timing – VW Passat B5 · 83 torque figures
- Removing and installing camshafts – VW Passat B6 · 39 torque figures
- Removing and installing coolant pump · 53 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.