Sealing flanges and dual-mass flywheel/drive plate - exploded view of components — AUDI
Sealing flanges and dual-mass flywheel/drive plate - exploded view of components on Audi: factory workshop procedure for engines AFN, AJQ, APP, ARY.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
Sealing flanges and dual-mass flywheel/drive plate - exploded view of components
Note
Service to the clutch
Manual gearbox
Rep. Gr.
30
Oil seal
Remove sealing flange
Item
prior to removing
Install using
fitting tool
10 - 203
Do not lubricate sealing lip of oil seal
Intermediate shaft sprocket
Installation position
Fig.
Ensure that Woodruff key
Item
is fitted
45 Nm
Use
counterhold tool
3036
to loosen and tighten
25 Nm
Oil seal
Renewing
Chapter
Do not lubricate sealing lip of oil seal
10 Nm
Sealing flange (front)
Before fitting sump, apply a thin coat of sealant to sealing points between sealing flange and cylinder block
Apply sealant prior to installing
Sealant
Parts catalogue
Gasket
Renew
Cylinder block
Removing and installing crankshaft
Chapter
Dismantling and assembling pistons and conrods
Chapter
Exhauster pump for brake servo
O-ring
Renew
Cover
10 Nm
20 Nm
Bracket for exhauster pump
O-ring
Renew
Oil seal
Renew
10 Nm
Sealing flange (rear) with oil seal
With gasket for cylinder block
Do not lubricate sealing lip of oil seal
Before fitting sump, apply a thin coat of sealant to sealing points between sealing flange and cylinder block
Apply sealant prior to installing
Sealant
Parts catalogue
To install, push guide sleeve from assembly kit onto crankshaft.
Gasket
Fit only if sealing flange has no sealing lip on cylinder block side
Dual-mass flywheel/drive plate
Removing and installing dual-mass flywheel
Chapter
Removing and installing drive plate
Chapter
Securing bolt for dual-mass flywheel/drive plate
Renew
Tightening torque: vehicles with manual gearbox
Anchor
; vehicles with automatic gearbox
Anchor
Intermediate plate
Must be positioned on dowel sleeves
Do not damage/bend when assembling
Is fitted on sealing flange
Fig.
Intermediate shaft
Axial clearance: max. 0.25 mm
Woodruff key
Check for firm attachment
O-ring
Renew
Sealing flange for intermediate shaft
25 Nm
Installation position of intermediate shaft sprocket
The deep shoulder
arrows
on the intermediate shaft sprocket faces towards the front.
The identification marking on the sprocket faces to the rear.
Installing intermediate plate
Fit intermediate plate to sealing flange and push onto dowel sleeves
arrows
.
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other AUDI procedures
- Testing coolant temperature sender -G62
- Checking EGR valve -N18
- Checking coolant temperature sender -G62
- Removing and installing dual mass flywheel/drive plate
- Removing, installing and testing injectors – Audi 1.9 TDI
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.