Removing and installing oil pump with balance shaft assembly, engine code BVY, BVZ — AUDI

🧭 Before you start

Fits: Audi A3 (8P, 2003–2012)

• Timing position: the crankshaft or camshaft is set and locked during this job

Don't miss

• Loosen bolt on oil pump chain sprocket. Counterhold on central bolt of vibration damper.
• Cut off tube nozzle at front marking (diameter of nozzle approx. 3 mm).
• The bead of sealant must not be thicker than specified, otherwise excess sealant can enter the sump and block the strainer in the oil intake pipe.
• Note different bolt lengths .
• Marking on chain sprocket of balance shaft (arrow) must be positioned opposite the locating hole. Use locking pin T10027 to lock chain sprocket in this position. Place chain on chain sprocket of balance shaft.

🔧 Engine codes this applies to

🔩 Torque settings

Values can differ between engine variants — check the code stamped on your block.

ℹ️ Always cross-check the exact figure against your vehicle's factory manual before final tightening — a wrong torque can damage the engine. These values are extracted from workshop data and may not cover every variant or revision.

📐 50 workshop diagrams for AXW

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

📋 Procedure

1. Remove sump: engine codes BVY, BVZ .
2. Pull off chain guard. Retaining tabs can be released with a small screwdriver (insert in openings (arrows)).
3. Loosen bolt on oil pump chain sprocket. Counterhold on central bolt of vibration damper.
4. Use screwdriver to slacken chain rail (arrow) and lock it in position using a 3 mm Allen key (1).
5. Detach oil pump chain sprocket and disengage chain at balance shaft drive.

6. Loosen bolts (arrows) on balance shaft assembly, working from outside inwards, and then remove balance shaft assembly.
7. Remove intermediate plate. [Note: The intermediate plate must always be renewed.Note the use-by date of the sealant.The balance shaft assembly with intermediate plate and sump must be installed and the securing bolts tightened immediately after the silicone sealant has been applied.]
8. Remove sealant residue from cylinder block using a flat scraper.
9. Cut off tube nozzle at front marking (diameter of nozzle approx. 3 mm).
10. Apply silicone sealant onto clean sealing surface of new intermediate plate as illustrated. [Note: The bead of sealant must not be thicker than specified, otherwise excess sealant can enter the sump and block the strainer in the oil intake pipe.]
11. Fit intermediate plate onto dowel sleeves on balance shaft assembly as shown (arrows).
12. Install oil pump with balance shaft assembly and intermediate plate. Tighten securing bolts (arrows) to 15 Nm + 1/4 turn (90°) further, working from inside outwards. [Note: Note different bolt lengths .] — 15 Nm (11 lb-ft)
13. Turn crankshaft to TDC of No. 1 cylinder.
14. Marking on chain sprocket of balance shaft (arrow) must be positioned opposite the locating hole. Use locking pin T10027 to lock chain sprocket in this position. Place chain on chain sprocket of balance shaft.
15. Install oil pump chain sprocket and hand-tighten the bolt. [Note: The oil pump chain sprocket can only be installed correctly in one position. When installing, you may ONLY turn the oil pump.]
16. Remove locking pin T10027 and Allen key (1). Secure oil pump chain sprocket. Counterhold on central bolt of vibration damper.

Other AUDI procedures

• Removing and installing engine control unit J623 – VW · 6 torque figures
• Adjusting assembly mountings – Audi A3 1.8 · 4 torque figures
• Removing cylinder head – Audi A3 · 1 torque figures
• Removing and installing exhaust gas temperature sender 1G235 · 1 torque figures
• Removing and installing toothed belt, engine code AXW, BMB, BHD · 1 torque figures
• Removing and installing toothed belt – Audi · 56 torque figures
• Removing engine – Audi A8 D3 · 41 torque figures
• Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
• Installing engine – Audi A8 D4 · 36 torque figures
• Removing and installing camshaft timing chain · 29 torque figures