TorqFix

Removing and installing oil level and oil temperature sender G266 — AUDI

Removing and installing oil level and oil temperature sender G266 on Audi: 12 steps, engines AEB, AFB, AJK, AJL.

Workshop procedure for AUDI — the exact step sequence and torque figures, straight from real workshop data.

12 steps 40 engine codes engine codes merged from 125 documented variants

🧭 Before you start

Fits: Audi Q7 (4L, 2005–2015)

Don't miss

  • Ignore items marked (2) and (arrows).
  • Renew seal (2).Hose connections and air pipes and hoses must be free of oil and grease before assembly.Secure all hose connections with the correct type of hose clips (same as original equipment) Electronic parts catalogue.

🔧 Engine codes this applies to

AEBAFBAJKAJLAKBAKCAKNANBAPBAPUAQFAQGAQHAREARKARUASEATWAUAAUKAUWAUXAVBAVFAVNAVPAWTAWXAXXAYSAZABADBARBBYBCSBDXBELBESBHZBKE

📐 46 workshop diagrams for AEB

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

Removing and installing oil level and oil temperature sender G266 — AEB · diagram 1
Removing and installing oil level and oil temperature sender G266 — AEB · diagram 2
Removing and installing oil level and oil temperature sender G266 — AEB · diagram 3
Removing and installing oil level and oil temperature sender G266 — AEB · diagram 4
Removing and installing oil level and oil temperature sender G266 — AEB · diagram 5
Removing and installing oil level and oil temperature sender G266 — AEB · diagram 6
Removing and installing oil level and oil temperature sender G266 — AEB · diagram 7
Removing and installing oil level and oil temperature sender G266 — AEB · diagram 8
+ 38 more diagrams
🔒 46 workshop diagrams for this job Ask about your Audi AEB — free or sign up free to see the drawings

📋 Procedure

  1. Drain off engine oil 406.
  2. Remove air filter element (left-side) 23.
  3. Release hose clips (arrows) and detach air pipe (1).
  4. Unplug electrical connector (2).
  5. Remove bolt (1) for coolant pipes. [Note: Ignore items marked (2) and (arrows).]
AEB? Steps differ between engine variants — check this job against your exact car before you commit to it. Check my car — free →
  1. Remove bolts (arrows) and push coolant pipes towards front of vehicle.
  2. Unplug electrical connector (3).
  3. Remove bolts (1) and detach oil level and oil temperature sender G266(item 4). [Note: Renew seal (2).Hose connections and air pipes and hoses must be free of oil and grease before assembly.Secure all hose connections with the correct type of hose clips (same as original equipment) Electronic parts catalogue.]
  4. Install air hoses with screw-type clips .
  5. Secure coolant pipes Air duct system - exploded view.
  6. Install air filter element 23.
  7. Fill with engine oil and check oil level 406.
Workshop diagrams

Ask TorqFix about your Audi AEB — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.

Ask about your Audi AEB — free → or sign up free to see the drawings

Other AUDI procedures

Who makes these pages, and how

TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.

The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.

Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.

Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com

The story behind TorqFix →

Workshop data on this page last updated 20 Sep 2026.