Replacing headlight bulb — VW
Replacing headlight bulb on VW: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for VW — the factory write-up, straight from real workshop data.
📋 Procedure
Note:
Do not touch bulb glass when fitting a new bulb. Fingers leave traces of grease on the glass, which when switching bulb on, evaporate and cause the glass to cloud over.
Replacing dipped beam bulb
Release spring clip -arrow- and take off sealing cover.
Pull connector -1- off bulb.
Push retaining clip -2- over the lugs -3- and release.
Pull bulb -4- out of reflector.
1 -
Connector
2 -
Retaining clip
3 -
Locating lugs
4 -
Dipped beam bulb
Do not touch bulb glass when installing.
Insert new bulb so that the lugs on the laminated plate align with the grooves in the reflector.
After installing a new bulb check headlight settings.
Replacing main beam bulb
Release spring clip -arrow- and take off sealing cover.
Pull connector -1- off bulb.
Push retaining clip -2- over the lugs -3- and release.
Pull bulb -4- out of reflector.
1 -
Connector
2 -
Retaining clip
3 -
Locating lugs
4 -
Main beam bulb
Do not touch bulb glass when installing new bulb.
Insert new bulb so that the lugs on the laminated plate align with the grooves in the reflector.
After installing a new bulb check headlight settings.
Replacing side light bulb
Release spring clip -arrow- and take off sealing cover.
Pull bulb with holder on connector out of reflector -arrow-.
After changing bulb, push bulb with holder fully into the reflector.
After installing a new bulb check headlight settings.
Replacing front turn signal bulb
Release spring clip -arrow- and take off sealing cover.
Turn bulb holder -arrow- to left and pull out of housing.
Remove bulb from the holder.
Install in reverse order.
When installing, ensure that the bulb holder engages in the bulb housing.
After installing a new bulb check headlight settings.
Replacing fog light bulb
Release spring clip -arrow- and take off sealing cover.
Pull connector -1- off bulb.
Push retaining clip -2- over the lugs -3- and release.
Pull bulb -4- out of reflector.
1 -
Connector
2 -
Retaining clip
3 -
Locating lugs
4 -
Fog light bulb
Do not touch bulb glass when installing.
Insert new bulb so that the lugs on the laminated plate align with the grooves in the reflector.
After installing a new bulb check headlight settings.
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other VW procedures
- Removing engine · 41 torque figures
- Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
- Adjusting valve timing – VW Passat B5 · 83 torque figures
- Removing and installing camshafts – VW Passat B6 · 39 torque figures
- Removing and installing coolant pump · 53 torque figures
- Removing and installing battery on left in luggage compartment · 2 torque figures
- Removing gearbox, vehicles with 1.6 l - 75 kW; 2.0 l - 85 kW; and 2.0 l - 110 kW engines
- VW Securing to assembly stand gearbox removal & installation · 3 torque figures
- Adjusting selector mechanism · 2 torque figures
- Removing and installing fresh air blower V2 – VW · 3 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.