Removing and installing starter (petrol engine) — VW
Removing and installing starter (petrol engine) on VW: 17 steps, 1 torque figure. What to remove, what to tighten and to how many Nm, what to check after.
Workshop procedure for VW — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
Fits: platform code 6N1
Don't miss
- On some vehicles the bolts (2) and (3) are secured with a clip.
- If necessary, secure bolts (2) and (3) with a clip.
🔩 Torque settings
Values can differ between engine variants — check the code stamped on your block.
| Torque | Fastener / step |
|---|---|
| 13 Nm (9.6 lb-ft) | Tighten wire terminal from solenoid switch (terminal 30) |
ℹ️ Always cross-check the exact figure against your vehicle's factory manual before final tightening — a wrong torque can damage the engine. These values are extracted from workshop data and may not cover every variant or revision.
📋 Procedure
- Disconnect earth strap at battery.
- Unclip line (1) from bracket (2).
- Unscrew hexagon bolt (3) and remove bracket (2).
- Release terminal 50 connector (1) and pull disconnect.
- Remove plastic cap (2) and disconnect wire from solenoid switch terminal 30.
- Remove hexagon bolt (1).
- Remove hexagon nut (4). [Note: On some vehicles the bolts (2) and (3) are secured with a clip.]
- Unscrew hexagon bolt (3) and remove bolt (2).
- Take starter out downwards.
- Insert starter.
- Insert hexagon bolts (1) and (3) and tighten hand-tight.
- Insert hexagon bolt (2) and tighten hexagon nut (4) hand-tight.
- Tighten hexagon bolts (1) and (3) and hexagon nut (4). [Note: If necessary, secure bolts (2) and (3) with a clip.]
- Reconnect terminal 50 connector (1).
- Tighten wire terminal from solenoid switch (terminal 30) to 13 Nm and fit plastic cap (2). — 13 Nm (9.6 lb-ft)
- Install bracket (2) and tighten hexagon bolt (arrow).
- Clip line (1) into bracket (2).
Other VW procedures
- Removing engine · 41 torque figures
- Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
- Adjusting valve timing – VW Passat B5 · 83 torque figures
- Removing and installing camshafts – VW Passat B6 · 39 torque figures
- Removing and installing coolant pump · 53 torque figures
- Generator (Alternator)C for 1.0 and 1.6-litre (CCNA, CCRA) engines - remove and install · 6 torque figures
- Removing and installing front sealing flange – VW Passat B5 · 6 torque figures
- Installing retaining bracket · 8 torque figures
- Installing battery · 7 torque figures
- Removing and installing auxiliary/supplementary heater – VW · 6 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.