Removing and installing reversing camera R189, Saloon — VW

🧭 Before you start

Fits: VW Passat B7 saloon (362, 2010–2014), VW Passat B7 Variant (365, 2010–2014)

📋 Procedure

1. Switch off ignition and all electrical consumers.
2. Disengage ignition key in position 0 (locked).
3. Release and detach connectors (2) and (3) from their holders.
4. Release and disconnect connectors (2) and (3).
5. Pull wiring retainer (1) of rear lid plate.

6. Remove rear lid lock General body repairs, exterior55Rear lid; Removing and installing rear lid lock.
7. Release connector (2) and disconnect.
8. Remove the 3 securing bolts (arrows) of swivel badge.
9. Turn swivel badge together with reversing camera and swivel motor (1) to right to stop and push inwards out of mounting in rear lid.
10. Pull drain hose out of hose nozzle on underside of swivel badge.
11. Remove swivel badge with reversing camera and swivel motor inwards out of rear lid.
12. ⚠ Danger of leakageTwisted or not properly positioned seals may result in danger of water ingress into the luggage compartment.Check that installed seals are in good condition and in proper installation position. — Check circumferential rubber seal (1) of swivel badge and ensure that it is completely inserted in groove.
13. Attach drain hose to hose nozzle on underside of swivel badge.
14. Lock swivel badge by turning it to left into its mounting in rear lid.
15. Start the 3 securing bolts (arrows) of swivel badge.
16. Align swivel badge centrally in rear lid aperture.
17. Tighten the 3 securing bolts (arrows).
18. Connect all connectors of reversing camera wiring harness and secure all wires and connectors with wire retainers to avoid rattling.
19. Install rear lid lock General body repairs, exterior55Rear lid; Removing and installing rear lid lock.
20. After installation, clean reversing camera lens with a lint-free cloth.
21. Recalibrate reversing camera .
22. Remove swivel badge with reversing camera and swivel motor housing from rear lid.
23. Release connector (5) and disconnect.
24. Undo and remove the 4 securing bolts (arrows).
25. Remove reversing camera housing (2) together with swivel motor (3) from swivel badge (4).
26. ⚠ Danger of leakageTwisted or not properly positioned seals may result in danger of water ingress into the luggage compartment.Check that installed seals are in good condition and in proper installation position. — Check seal between camera and swivel badge and make sure that it has not come off or been twisted.
27. Clip in swivel motor wire before reinstalling it into wire securing clamp (1) behind camera housing.
28. Insert reversing camera housing (1) together with swivel motor (3) into swivel badge (4).
29. ⚠ Swivel mechanism may become stuck.The securing bolt in swivel motor, which is difficult to reach, (bottom right arrow), can drop into reversing camera housing during positioning.To position bolt, turn swivel badge so that swivel motor (3) is underneath. — Remove reversing camera with swivel motor from swivel badge.
30. Unclip swivel motor wire (3) from wire guide (1) behind camera.
31. Remove the two securing bolts (2) from swivel motor.
32. Carefully detach reversing camera housing from swivel motor.
33. Check if release lever and sliding surfaces on swivel motor are greased sufficiently.
34. Carefully fit reversing camera housing to swivel motor.

Other VW procedures

• Removing engine · 41 torque figures
• Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
• Adjusting valve timing – VW Passat B5 · 83 torque figures
• Removing and installing camshafts – VW Passat B6 · 39 torque figures
• Removing and installing coolant pump · 53 torque figures
• Dismantling and assembling pistons and conrods
• Removing and installing pinion shaft and dismantling and assembling
• Removing and installing steering column with column tube, vehicles as of 07.84
• Removing and installing gearbox, 1.4 l - 90 kW TSI engine
• Removing and installing housing