Installation continuation: VW 2.0 (BBX, CFEA)
Step-by-step installation continuation for the VW 2.0 (BBX/CFEA): 11 steps, 3 torque figures. What to remove, what to tighten and to how many Nm, what to.
Workshop procedure for VW — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
Fits: platform codes 9A2, 9A4, 9A5, 9A6, 9A1, 9A3
Don't miss
- Tightening torque for the assembly mountings .
- In the installation of the Poly-V belt, make sure there is the right seating of the belt on the respective pulleys.
🔩 Torque settings
Values can differ between engine variants — check the code stamped on your block.
| Torque | Fastener / step |
|---|---|
| 25 Nm (18 lb-ft) | Install Poly-V belt tensioning element |
| 25 Nm (18 lb-ft) | Tighten the pulley/vibration damper |
| 50 Nm (37 lb-ft) | Install engine support in the cylinder block |
ℹ️ Always cross-check the exact figure against your vehicle's factory manual before final tightening — a wrong torque can damage the engine. These values are extracted from workshop data and may not cover every variant or revision.
📐 15 workshop diagrams for BBX
Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.
📋 Procedure
- Tighten the pulley/vibration damper. Tightening torque: 25 Nm. — 25 Nm (18 lb-ft)
- Install mechanical distributor central cover.
- Install engine support in the cylinder block. Tightening torque 50 Nm. — 50 Nm (37 lb-ft)
- Completely install the engine assembly mountings. [Note: Tightening torque for the assembly mountings .]
- Remove the Bracket or VW 06110-222A.
- Install the upper cover of the mechanical distribution.
- Install Poly-V belt tensioning element. Tightening torque: 25 Nm. — 25 Nm (18 lb-ft)
- Install Poly-V belt . [Note: In the installation of the Poly-V belt, make sure there is the right seating of the belt on the respective pulleys.]
- Install coolant reservoir.
- Install the right front wheel case cover: General body repairs, exterior66External equipment.
- Install the lower engine noise insulation Body - External assembly works50Body - front part.
Ask TorqFix about your VW BBX — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.
Ask about your VW BBX — free → or sign up free to see the drawingsOther VW procedures
- Camshaft - repair
- Checking conditions – VW 2.0
- Crankshaft - remove and install
- Crankshaft and flywheel flanges - remove and install
- Exploded view crankshaft
- Removing engine · 41 torque figures
- Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
- Adjusting valve timing – VW Passat B5 · 83 torque figures
- Removing and installing camshafts – VW Passat B6 · 39 torque figures
- Removing and installing coolant pump · 53 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.