TorqFix

Checking current draw, engine code CDGA: VW Touran I 1.4 (CDGA)

Step-by-step checking current draw, engine code CDGA for the VW Touran I 1.4 (CDGA): 11 steps. What to remove, in what order, and what to check after.

Workshop procedure for VW — the exact step sequence and torque figures, straight from real workshop data.

11 steps 1 engine code

🧭 Before you start

Fits: VW Touran I (1T, 2003–2015)

  • Renewed: fuel delivery unit

Don't miss

  • First, ensure that connector is fitted securely by pulling it without pressing catch.
  • If the fuel system malfunction is intermittent, the check can be performed during a road test, but a 2nd person is necessary.

🔧 Engine codes this applies to

CDGA

📐 41 workshop diagrams for CDGA

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

Checking current draw, engine code CDGA — CDGA · diagram 1
Checking current draw, engine code CDGA — CDGA · diagram 2
Checking current draw, engine code CDGA — CDGA · diagram 3
Checking current draw, engine code CDGA — CDGA · diagram 4
Checking current draw, engine code CDGA — CDGA · diagram 5
Checking current draw, engine code CDGA — CDGA · diagram 6
Checking current draw, engine code CDGA — CDGA · diagram 7
Checking current draw, engine code CDGA — CDGA · diagram 8
+ 33 more diagrams
🔒 41 workshop diagrams for this job Ask about your VW CDGA — free or sign up free to see the drawings

📋 Procedure

  1. Observe safety precautions (see the separate procedure).
  2. Observe rules for cleanliness (see the separate procedure).
  3. Observe safety precautions when working on natural gas system (see the separate procedure).
  4. Fold rear seats forwards.
  5. Release carpet under seats, and fold it to rear General body repairs, interior 70. Load and luggage compartment trims; Removing and installing load compartment floor.
CDGA? Steps differ between engine variants — check this job against your exact car before you commit to it. Check my car — free →
  1. Remove cover (1) under rear bench seat.
  2. First, ensure that connector is fitted securely by pulling it without pressing catch.
  3. Using pick-up clamp, connect multimeter V.A.G 1715 to red/green wire to fuel pump control unit.
  4. Run engine at idling speed.
  5. Measure current draw of fuel pump. [Note: If the fuel system malfunction is intermittent, the check can be performed during a road test, but a 2nd person is necessary.]
  6. Fuel pump is defective; renew fuel delivery unit (see the separate procedure).
Workshop diagrams

Ask TorqFix about your VW CDGA — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.

Ask about your VW CDGA — free → or sign up free to see the drawings

Other VW procedures

Who makes these pages, and how

TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.

The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.

Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.

Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com

The story behind TorqFix → · How these pages are made →

Workshop data on this page last updated 20 Sep 2026.