Assembly overview - clutch hydraulics, Scirocco, CC, Golf Cabriolet, Passat, RHD vehicles — VW
Assembly overview - clutch hydraulics, Scirocco, CC, Golf Cabriolet, Passat, RHD vehicles on VW: factory workshop procedure.
Workshop procedure for VW — the factory write-up, straight from real workshop data.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
Assembly overview - clutch hydraulics, Scirocco, CC, Golf Cabriolet, Passat, RHD vehicles
Brake fluid reservoir
Seal
For plastic supply hose
If damaged, renew together with supply hose
The seals must be located in supply hose
Supply hose
Clutch master cylinder
Removing and installing
Chapter
Clip
Pull clip out to stop to remove or install pipe line
Pulled out to side on some clutch master cylinders
Seal / O-ring
Renew if damaged
Pull onto line connection
Insert with brake fluid
Seals/O-rings are adapted to configuration of line connection
Fig.
Allocation
Electronic Parts Catalogue
Retainer
To remove and install, separate clutch master cylinder from clutch pedal
Chapter
“
Removing and installing clutch pedal
”
Clutch pedal
Removing and installing
Chapter
.
Hexagon nut
Specified tightening torque
Chapter
Bracket
Secured to body
Hidden by engine/gearbox mounting
Pipe line
Pipe and pipe/hose assembly may be in one piece.
Allocation
Electronic Parts Catalogue
To remove, remove battery and battery tray
Electrical system
Rep. gr.
27
Battery; Removing and installing battery
.
Seal / O-ring
Renew if damaged
Pull onto line connection
Insert with brake fluid
Seals/O-rings are adapted to configuration of line connection
Fig.
Allocation
Electronic Parts Catalogue
Pipe/hose assembly
Pipe and pipe/hose assembly may be in one piece.
Allocation
Electronic Parts Catalogue
To remove, remove battery and battery tray
Electrical system
Rep. gr.
27
Battery; Removing and installing battery
.
Bracket
Secured to body depending on vehicle equipment
Seal / O-ring
Renew if damaged
Pull onto line connection
Insert with brake fluid
Seals/O-rings are adapted to configuration of line connection
Fig.
Allocation
Electronic Parts Catalogue
Clip
Pull out clip to stop to remove and install pipe/hose assembly or bleeder.
Bleeder valve
Bleeding clutch mechanism
Chapter
With hexagon, specified torque: 4.5 Nm
Flattened on both sides: close as far as stop
Dust cap
Bleeder
Seal / O-ring
Renew if damaged
Pull onto line connection
Insert with brake fluid
Seals/O-rings are adapted to configuration of line connection
Fig.
Allocation
Electronic Parts Catalogue
Clutch slave cylinder
Can be renewed only with gearbox removed
Removing and installing
Chapter
Gearbox
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other VW procedures
- Removing engine · 41 torque figures
- Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
- Adjusting valve timing – VW Passat B5 · 83 torque figures
- Removing and installing camshafts – VW Passat B6 · 39 torque figures
- Removing and installing coolant pump · 53 torque figures
- Removing and installing gas pressure regulator – VW 2.0
- Removing and installing brake master cylinder, LHD vehicles
- Checking cooling output on vehicles with manually controlled air conditioning system
- Removing and installing battery, vehicles with high-voltage system
- Removing and installing centre console insert – VW Passat B8
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.