Adjusting assembly mountings (Passat 2006 ▶, CC) — VW
Adjusting assembly mountings (Passat 2006 ▶, CC) on VW: 13 steps, engines BZB, CAWA, CAWB, CBFA. What to remove, in what order, and what to check after.
Workshop procedure for VW — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
Fits: VW Passat B6 (3C, 2005–2010), VW Passat CC (357, 2008–2012)
Don't miss
- Support engine with gearbox, but do not raise.
📐 74 workshop diagrams for BZB
Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.
📋 Procedure
- Remove engine cover panel (see the separate procedure).
- Remove air filter (see the separate procedure).
- ⚠ To prevent damage to the electronic components when disconnecting the battery:Observe notes on procedure for disconnecting the battery. — With ignition switched off, disconnect battery earth cable (arrow).
- Remove battery (repair group 27).
- Remove battery tray (arrows).
- Fit support bracket10 - 222 A, as shown, with the following tool parts. [Note: The adapters10 - 222 A /8 must not be located on the screw plates of the wings, as this will otherwise cause damage to them. The shackle10 - 222 A /12 is needed so the engine is raised in its installation position and does not »fall back«.]
- Support engine with gearbox, but do not raise.
- Renew assembly mounting bolts (arrows) on engine side one after the other (if not already carried out during engine installation) and screw in hand-tight.
- Renew assembly mounting bolts (arrows) on gearbox side one after the other (if not already carried out during engine installation) and screw in hand-tight.
- Renew assembly mounting bolts (arrows) on gearbox side one after the other (if not already carried out during engine installation) and screw in hand-tight.
- Slacken bolts on left and right-hand support arms by about two turns each.
- Adjust assembly mounting and tighten securing bolts hand-tight.
- Tighten bolts for assembly mounting to required specified torque (value given in the factory table, not available here).
Ask TorqFix about your VW BZB — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.
Ask about your VW BZB — free → or sign up free to see the drawingsOther VW procedures
- Removing and installing coarse oil separator · 1 torque figures
- VW T5 ancil drive auxiliary belt replacement
- Renewing oil seal for balance shaft (inlet side) – Audi A3
- Removing and installing air filter element – VW Touareg II
- Cleaning injectors – Audi A3 2.0
- Removing engine · 41 torque figures
- Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
- Adjusting valve timing – VW Passat B5 · 83 torque figures
- Removing and installing camshafts – VW Passat B6 · 39 torque figures
- Removing and installing coolant pump · 53 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix → · How these pages are made →Workshop data on this page last updated 20 Sep 2026.