TorqFix

308 DV6TED4 — PEUGEOT

308 DV6TED4 on Peugeot: 41 steps, engines DV6TED4(9HV), DV6TED4(9HZ). What to remove, in what order, and what to check after.

Workshop procedure for PEUGEOT — the exact step sequence and torque figures, straight from real workshop data.

41 steps 2 engine codes

🔧 Engine codes this applies to

DV6TED4(9HV)DV6TED4(9HZ)

📐 27 workshop diagrams for DV6TED4(9HV)

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

308 DV6TED4 — DV6TED4(9HV) · diagram 1
308 DV6TED4 — DV6TED4(9HV) · diagram 2
308 DV6TED4 — DV6TED4(9HV) · diagram 3
308 DV6TED4 — DV6TED4(9HV) · diagram 4
308 DV6TED4 — DV6TED4(9HV) · diagram 5
308 DV6TED4 — DV6TED4(9HV) · diagram 6
308 DV6TED4 — DV6TED4(9HV) · diagram 7
308 DV6TED4 — DV6TED4(9HV) · diagram 8
+ 19 more diagrams
🔒 27 workshop diagrams for this job Ask about your Peugeot DV6TED4(9HV) — free or sign up free to see the drawings

📋 Procedure

Preparation and removal

  1. Caution! The temperature of the engine and exhaust will increase significantly
  2. Raise the vehicle
  3. Remove the underbody cover
  4. Disconnect the connector
  5. Start the engine
DV6TED4(9HV)? Steps differ between engine variants — check this job against your exact car before you commit to it. Check my car — free →
  1. Reinforcement brace:
  2. Remove the brace
  3. Remove the additive tank
  4. Connect the diagnostic tool
  5. Read out the fault codes
  6. Delete all the fault codes
  7. Note: Plug all open lines to prevent damage
  8. Caution! Note the additive hazard warnings
  9. Stage 2:
  10. Engine running at idle speed

Installation and checks

  1. Renew the additive reservoir
  2. Refit all other parts in the reverse order of removal
  3. Note: Do not re-use the drained fluid or fluid from opened containers
  4. Stage 3:
  5. Run the engine at idle speed
  6. Wait until the engine has cooled down
  7. Stop the engine
Workshop diagrams

Ask TorqFix about your Peugeot DV6TED4(9HV) — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.

Ask about your Peugeot DV6TED4(9HV) — free → or sign up free to see the drawings

Other PEUGEOT procedures

Who makes these pages, and how

TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.

The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.

Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.

Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com

The story behind TorqFix →

Workshop data on this page last updated 20 Sep 2026.