TorqFix

Cylinder head removal & torque: Peugeot 206, 307 (TU5JP4)

Step-by-step cylinder head removal & torque for the Peugeot 206, 307 (TU5JP4): 39 steps. What to remove, in what order, and what to check after.

Workshop procedure for PEUGEOT — the exact step sequence and torque figures, straight from real workshop data.

39 steps 2 engine codes

🧭 Before you start

Fits: platform codes 1.6, 16V, |, BIOFLEX, CC

  • Opens: fuel
  • Timing position: the crankshaft or camshaft is set and locked during this job

🔧 Engine codes this applies to

TU5JP4(N6A)TU5JP4(NFU)

📐 21 workshop diagrams for TU5JP4(N6A)

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

206, 307 TU5JP4 kop uit in — TU5JP4(N6A) · diagram 1
206, 307 TU5JP4 kop uit in — TU5JP4(N6A) · diagram 2
206, 307 TU5JP4 kop uit in — TU5JP4(N6A) · diagram 3
206, 307 TU5JP4 kop uit in — TU5JP4(N6A) · diagram 4
206, 307 TU5JP4 kop uit in — TU5JP4(N6A) · diagram 5
206, 307 TU5JP4 kop uit in — TU5JP4(N6A) · diagram 6
206, 307 TU5JP4 kop uit in — TU5JP4(N6A) · diagram 7
206, 307 TU5JP4 kop uit in — TU5JP4(N6A) · diagram 8
+ 13 more diagrams
🔒 21 workshop diagrams for this job Ask about your Peugeot TU5JP4(N6A) — free or sign up free to see the drawings

📋 Procedure

  1. Remove the engine covers
  2. Remove the air filter together with the air duct and resonance duct
  3. Disconnect the battery
  4. Check the surfaces for damage
  5. Check that the centering bushes are present
TU5JP4(N6A)? Steps differ between engine variants — check this job against your exact car before you commit to it. Check my car — free →
  1. Remove the crankshaft pulley
  2. Support the engine
  3. Remove the right-hand engine support
  4. Remove:
  5. Cylinder head torque settings - Refer to 'Adjustment data/Torque settings'
  6. Remove the timing belt lower cover
  7. Remove:
  8. Dipstick tube:
  9. Remove the catalytic converter
  10. Fit the special tools
  11. Lock the camshaft gearwheels
  12. Lock the flywheel
  13. Remove the cover
  14. Remove the ignition coils
  15. Remove the valve covers
  16. Disconnect the heater hose
  17. Disconnect the connectors
  18. Release the fuel pressure
  19. Disconnect the MAP sensor connector
  20. Disconnect the fuel lines
  21. Disconnect the throttle cable
  22. Remove the cylinder head bolts
  23. Remove the cylinder head
  24. Note:
  25. Use a special tool:
Workshop diagrams

Ask TorqFix about your Peugeot TU5JP4(N6A) — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.

Ask about your Peugeot TU5JP4(N6A) — free → or sign up free to see the drawings

Other PEUGEOT procedures

Who makes these pages, and how

TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.

The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.

Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.

Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com

The story behind TorqFix →

Workshop data on this page last updated 20 Sep 2026.