TorqFix

Timing belt replacement: Lancia Zeta 2.0 RFV Ancill drive (XU10J4R)

Step-by-step timing belt replacement for the Lancia Zeta 2.0 RFV Ancill drive (XU10J4R): 19 steps. What to remove, in what order, and what to check after.

Workshop procedure for LANCIA — the exact step sequence and torque figures, straight from real workshop data.

19 steps 1 engine code

🧭 Before you start

  • Timing position: the crankshaft or camshaft is set and locked during this job
  • Special tools named: locking pin

🔧 Engine codes this applies to

XU10J4R(RFV)

📐 33 workshop diagrams for XU10J4R(RFV)

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

Zeta 2.0 16V (RFV) Ancill drive belt — XU10J4R(RFV) · diagram 1
Zeta 2.0 16V (RFV) Ancill drive belt — XU10J4R(RFV) · diagram 2
Zeta 2.0 16V (RFV) Ancill drive belt — XU10J4R(RFV) · diagram 3
Zeta 2.0 16V (RFV) Ancill drive belt — XU10J4R(RFV) · diagram 4
Zeta 2.0 16V (RFV) Ancill drive belt — XU10J4R(RFV) · diagram 5
Zeta 2.0 16V (RFV) Ancill drive belt — XU10J4R(RFV) · diagram 6
Zeta 2.0 16V (RFV) Ancill drive belt — XU10J4R(RFV) · diagram 7
Zeta 2.0 16V (RFV) Ancill drive belt — XU10J4R(RFV) · diagram 8
+ 25 more diagrams
🔒 33 workshop diagrams for this job Ask about your Lancia XU10J4R(RFV) — free or sign up free to see the drawings

📋 Procedure

Preparation and removal

  1. Disconnect the battery
  2. Remove the front right wheel
  3. Remove the front right splash guard
  4. Support the engine
  5. Remove the right-hand engine support
XU10J4R(RFV)? Steps differ between engine variants — check this job against your exact car before you commit to it. Check my car — free →
  1. Remove the timing belt cover
  2. Remove the reinforcement brace
  3. Move the coolant pipe aside slightly
  4. Loosen the bolts
  5. Remove the ancillary drive belt
  6. Fit the locking pin

Installation and checks

  1. Remove the locking pin
  2. Tighten the bolts
  3. Refit the reinforcement brace
  4. Fit the timing belt cover
  5. Refit the right-hand engine support
  6. Refit the front right splash guard
  7. Refit the front right wheel
  8. Reconnect the battery
Workshop diagrams

Ask TorqFix about your Lancia XU10J4R(RFV) — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.

Ask about your Lancia XU10J4R(RFV) — free → or sign up free to see the drawings

Other LANCIA procedures

Who makes these pages, and how

TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.

The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.

Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.

Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com

The story behind TorqFix → · How these pages are made →

Workshop data on this page last updated 20 Sep 2026.