Servicing selector mechanism on vehicles up to 11.2005 - exploded view — AUDI
Servicing selector mechanism on vehicles up to 11.2005 - exploded view on Audi: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
Audi
Audi A6
2005
Power transmission
Automatic gearbox 09L, four-wheel drive
Edition
12.2011
Servicing selector mechanism on vehicles up to 11.2005 - exploded view
WARNING
Prior to performing work with engine running, move selector lever to position
„P“
and pull up parking brake button to apply the electromechanical parking brake.
Check selector mechanism before dismantling
Chapter
.
Securing clip
Noise insulation
Retaining clip
Secures selector lever cable to shift unit
Selector lever cable
Do not bend or kink
Chapter
„
Removing and installing selector lever cable on vehicles up to 11.2005
“
Selector lever cable must be renewed if rubber sleeve is damaged
Before installing, lightly lubricate ball socket with
polycarbamide grease
G 052 142 A2
.
When installing, make sure that rubber sleeve on gearbox end is not twisted
Chapter
„
Adjusting selector lever cable on vehicles up to 11.2005
“
Clamping bolt
13 Nm
Pin for selector lever cable
To remove selector lever cable, pull plastic securing spring on selector mechanism forwards slightly and push up pin just far enough to release cable.
Selector lever lock solenoid
N110
Chapter
„
Removing and installing
selector lever lock solenoid
N110
on vehicles up to 11.2005
“
Selector lever position display
Y26
Chapter
„
Removing and installing
display unit for selector lever position
Y26
on vehicles up to 11.2005
“
Clamp
Secures selector lever handle to selector lever
Removing and installing
Chapter
„
Removing and installing selector lever handle on vehicles up to 11.2005
“
Selector lever boot
Detaching from selector lever handle
Chapter
Selector lever handle
Chapter
„
Removing and installing selector lever handle on vehicles up to 11.2005
“
Trim ring
Removing and installing
Chapter
„
Detaching selector lever boot from selector lever handle on vehicles up to 11.2005
“
Bolt
1.2 Nm
Selector lever sensors control unit
J587
and
tiptronic switch
F189
Chapter
„
Removing and installing
selector lever sensors control unit
J587
and
tiptronic switch
F189
on vehicles up to 11.2005
“
Gear selector position P switch
F305
Chapter
„
Removing and installing
gear selector position P switch
F305
on vehicles up to 11.2005
“
Nut
10 Nm
Shift unit
Can only be renewed as a complete unit
Chapter
„
Removing and installing shift unit on vehicles up to 11.2005
“
Noise insulation
Nut
10 Nm
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.