Servicing selector mechanism - exploded view — AUDI
Servicing selector mechanism - exploded view on Audi: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
Audi
Audi Q7
2007
Power transmission
Automatic gearbox 0AT, four-wheel drive
Edition
07.2006
Servicing selector mechanism - exploded view
WARNING
Before working on vehicle while engine is running, shift selector lever into position
“P”
and apply parking brake.
Overview:
Selector lever cable
Do not bend or kink
Chapter
“
Selector lever cable - exploded view
”
Chapter
“
Removing and installing selector lever cable
”
Chapter
“
Adjusting selector lever cable
”
Securing clip
Assembly instructions
Chapter
“
Selector lever cable - exploded view
”
Pin for selector lever cable
Assembly instructions
Chapter
“
Selector lever cable - exploded view
”
Clip
Secures selector lever handle to selector lever
Removing and installing
Chapter
“
Servicing selector lever handle - exploded view
”
Selector lever boot
Detaching from selector lever handle
Chapter
“
Servicing selector lever handle - exploded view
”
Trim ring
Removing and installing
Chapter
Selector lever handle
Chapter
“
Servicing selector lever handle - exploded view
”
Chapter
“
Removing and installing selector lever handle
”
Display unit for selector lever position
Y26
Removing and installing
Chapter
Bolt
1 Nm
4x
Selector lever sensors control unit
J587
and
tiptronic switch
F189
Removing and installing
Chapter
Selector lever lock solenoid
N110
Removing and installing
Chapter
Chapter
“
Operating manual release for selector mechanism
”
Shift unit
Checking operation:
Chapter
“
Checking selector mechanism
”
Chapter
“
Removing and installing shift unit
”
Chapter
“
Dismantling and assembling shift unit - exploded view
”
With
gear selector position P switch
F305
fitted,
Chapter
“
Removing and installing
gear selector position P switch
F305
”
Bolt
6.5 Nm
4x
Secures shift unit to cover for shift unit
With additional thread on bolt head (to secure centre console bracket)
Bolt
6.4 Nm
2x
Secures centring bracket to bottom cover for shift unit
Bolt
10 Nm
4x
Secures cover for shift unit to body
Cover for shift unit
Chapter
“
Removing and installing cover for shift unit
”
Centring bracket
Only required during production, does not have to be re-installed if damaged or removed
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- Checking lambda control and lambda probe -G39 and -G108 upstream of catalytic converter
- Checking lambda control and lambda probe -G130 and -G131 downstream of catalytic converter
- Installing air hoses and hose clips – Audi 5.0 BUH
- Removing and installing fuel gauge sender 3 G237 (up to model year 2013)
- Adjusting selector mechanism (vehicles from 11.00 onwards)
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.