Servicing selector mechanism on vehicles from 11.2005 onwards - exploded view — AUDI
Servicing selector mechanism on vehicles from 11.2005 onwards - exploded view on Audi: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
Audi
Audi A6
2005
Power transmission
Automatic gearbox 09L, four-wheel drive
Edition
12.2011
Servicing selector mechanism on vehicles from 11.2005 onwards - exploded view
WARNING
Prior to performing work with engine running, move selector lever to position
„P“
and pull up parking brake button to apply the electromechanical parking brake.
Check selector mechanism before dismantling
Chapter
.
Selector lever handle
Chapter
„
Selector lever handle and
display unit for selector lever position
Y26
on vehicles from 11.2005 onwards - exploded view
“
Trim ring
Removing and installing
Chapter
Selector lever boot
Removing and installing
Chapter
Clamp
Secures selector lever handle to selector lever
Removing and installing
Chapter
Selector lever position display
Y26
Chapter
„
Removing and installing
display unit for selector lever position
Y26
on vehicles from 11.2005 onwards
“
Nut
10 Nm
Secures selector mechanism to body
4x
Rubber seal
Selector lever sensors control unit
J587
and
tiptronic switch
F189
Chapter
„
Removing and installing
selector lever sensors control unit
J587
and
tiptronic switch
F189
on vehicles from 11.2005 onwards
“
Shift unit
Can only be renewed as a complete unit
Chapter
„
Removing and installing shift unit on vehicles from 11.2005 onwards
“
Selector lever lock solenoid
N110
Chapter
„
Removing and installing
selector lever lock solenoid
N110
on vehicles from 11.2005 onwards
“
Gear selector position P switch
F305
Consists of two microswitches on printed circuit board in
selector lever lock solenoid
N110
Can only be renewed together with
selector lever lock solenoid
N110
,
Chapter
„
Removing and installing
selector lever lock solenoid
N110
on vehicles from 11.2005 onwards
“
Noise insulation
Different versions
Electronic parts catalogue
Not fitted on all vehicles
Retaining washers
For securing noise insulation to shift unit
4x
Renew
Retaining clip
Secures selector lever cable to shift unit
O-ring
Renew
Selector lever cable
Do not bend or kink
Chapter
„
Selector lever cable on vehicles from 11.2005 onwards - exploded view
“
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- Installing exhaust system stress-free - vehicles with front-wheel drive
- Renewing seal for flange shaft
- Checking cruise control system (CCS) - petrol engines with electronic throttle
- Zero position compensation of steering angle sender -G85
- Checking fuel delivery (of metering pump -V54)
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.