Removing and installing parking brake switch F234 — AUDI
Removing and installing parking brake switch F234 on Audi: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
📋 Procedure
Removing and installing
parking brake switch
F234
Special tools and workshop equipment required
Removal wedge
3409
Removing
Remove rear centre console
Rep. gr.
68
.
Move seats back as far as possible.
On vehicles with automatic gearbox, move selector lever to position
“S”
.
Switch off ignition and take out ignition key.
Take hold of
Climatronic control unit
J255
(control and display unit) at bottom recesses.
Pull
Climatronic control unit
J255
(control and display unit) out of mounting frame
arrows
.
Place the
Climatronic control unit
J255
(control and display unit) down onto centre console (place a cloth beneath to prevent damage to surface).
Release retaining clip
F
and unplug electrical connectors in the sequence
A ... D
.
Unplug electrical connector
E
.
Pull off trim cover above ashtray
arrow
.
Open front ashtray.
Remove front ashtray insert.
Remove bolts
1
and
2
.
Release ashtray
3
using a screwdriver
arrow
(by applying screwdriver to opening
4
).
Remove front ashtray housing.
Unplug electrical connector if fitted.
Unclip boot
1
for gear lever (or selector lever on automatic gearbox) on both sides and pull off upwards
arrows
.
Vehicles with automatic gearbox:
Release retaining spring
2
and remove
selector lever display unit
Y26
item 1
upwards.
Unplug electrical connector.
All vehicles:
Unscrew bolts
arrows
.
Raise centre console (front)
1
at rear slightly and pull it off dash panel towards rear.
Unplug electrical connectors.
Unscrew bolts
arrows
.
Release the retaining clips
1 ... 3
and
6
on the trim frame
5
carefully with a thin screwdriver.
Remove trim frame together with
multimedia system operating unit
E380
4
upwards out of front centre console.
Unscrew bolts
arrows
.
Detach
parking brake switch
F234
item 1
at switch trim.
Installing
Installation is carried out in the reverse order; note the following:
Install rear centre console
Rep. gr.
68
.
Tightening torques
Component
Nm
Parking brake switch
F234
to switch trim
0.8
Multimedia system operating unit
E380
to centre console (front)
3
Centre console (front) to frame for centre console
3
Ashtray housing to frame for centre console (front)
3
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- RS6 (4F) BUH ancillary drive belt
- Contact assignment and operation of coolant shut-off valve relay -J541
- Dismantling and assembling drive pinion and hollow shaft from 05.03 >
- Gearbox (front-wheel drive) - code letters, gearbox allocation, ratios, equipment
- Removing engine - vehicles with four-wheel drive with engine codes BMN, BUY
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.