Removing and installing mounting bracket with clutch master cylinder - vehicles up to model year 2014 — AUDI

🧭 Before you start

Fits: Audi A1 (8X, 2010–2018)

• Opens: brake fluid, clutch fluid
• Special tools named: 3094
• Renewed: self-locking nuts

Don't miss

• In the following steps make sure that no brake fluid escapes onto the longitudinal member or onto the gearbox below. If this does happen, clean the affected area thoroughly.Place a cloth underneath to catch escaping brake fluid.
• Clamping off the supply hose with the hose clamp3094 will cause a permanent deformation.However, this does not damage the supply hose.After removing the hose clamp 3094, the supply hose must be returned to its original shape.
• (Item 1) can be disregarded.
• When working in the footwell, put cloths on the floor covering to protect it from possible brake fluid spills.
• Glue new gasket onto clutch master cylinder and mounting bracket.Renew self-locking nuts.After detaching hose clip, move supply hose to original position if necessary.

📋 Procedure

1. Remove air cleaner housing 24Air cleaner; Removing and installing air cleaner housing.
2. If necessary, remove engine control unit J623 from bracket at plenum chamber partition panel; release catches (arrows) to do so. [Note: In the following steps make sure that no brake fluid escapes onto the longitudinal member or onto the gearbox below. If this does happen, clean the affected area thoroughly.Place a cloth underneath to catch escaping brake fluid.]
3. Using hose clamp3094, clamp off supply hose to clutch master cylinder. [Note: Clamping off the supply hose with the hose clamp3094 will cause a permanent deformation.However, this does not damage the supply hose.After removing the hose clamp 3094, the supply hose must be returned to its original shape.]
4. Disconnect supply hose from clutch master cylinder and plug hose using sealing tool T10249/1.
5. Release retaining clip (2) with a screwdriver and disconnect pipe/hose assembly (3) from clutch master cylinder.

6. Unclip clutch position sender G476(arrows A, B) and place it to one side with electrical connector attached. [Note: (Item 1) can be disregarded.]
7. Remove dash panel cover (driver side) General body repairs, interior68Shelves / trim panels; Removing and installing dash panel cover (driver side).
8. Remove crash bar General body repairs, interior70Central tube for dash panel; Exploded view - central tube for dash panel. [Note: When working in the footwell, put cloths on the floor covering to protect it from possible brake fluid spills.]
9. Remove nuts (1 and 2).
10. Remove mounting bracket (3) with clutch master cylinder. [Note: Glue new gasket onto clutch master cylinder and mounting bracket.Renew self-locking nuts.After detaching hose clip, move supply hose to original position if necessary.]
11. Push pipe/hose assembly onto connection on clutch master cylinder so that retaining clip snaps into place.
12. Pull on pipe to check that it is secure.
13. Bleed clutch system .
14. Install clutch position sender G476.
15. If removed previously, attach engine control unit J623 to plenum chamber partition panel.
16. Install crash bar General body repairs, interior70Central tube for dash panel; Exploded view - central tube for dash panel.
17. Install dash panel cover (driver side) General body repairs, interior68Shelves / trim panels; Removing and installing dash panel cover (driver side).
18. Install air cleaner housing 24Air cleaner; Removing and installing air cleaner housing.

Other AUDI procedures

• Removing and installing toothed belt – Audi · 56 torque figures
• Removing engine – Audi A8 D3 · 41 torque figures
• Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
• Installing engine – Audi A8 D4 · 36 torque figures
• Removing and installing camshaft timing chain · 29 torque figures
• Removing and installing radiator cowl with radiator fan – Audi
• Removing and installing desiccant bag/desiccant cartridge - RS models · 1 torque figures
• Renewing brake caliper (1LT / 1LY) · 1 torque figures
• Renewing brake caliper (1LA / 1LB / 1LJ / 1LD / 1ZT + S4 / S5) · 1 torque figures
• Removing and installing power steering pump (vehicles with 6 cylinder 3.0 ltr. MPI engine)