Removing and installing brake caliper (1LP): Audi A6/A7 C7
Step-by-step removing and installing brake caliper (1LP) for the Audi A6/A7 C7: 12 steps. What to remove, in what order, and what to check after.
Workshop procedure for AUDI — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
Fits: Audi A6/A7 C7 (4G, 2011–2018); platform code 4X
- Opens: brake fluid
Don't miss
- Brake caliper must not be dismantled. Do not loosen any bolts on the brake caliper.
📋 Procedure
- ⚠ Escaping brake fluid can cause the vehicle to become dirty and may damage the paintwork.If the brake pads are worn and brake fluid has been topped up, brake fluid can overflow when the piston is pressed back into the brake cylinder.Before pressing the pistons back, check the brake fluid level. If the brake fluid is up to the "“MAX”" mark, fluid must be extracted.Use brake filling and bleeding equipmentVAS 5234 to extract brake fluid from brake fluid reservoir. — Remove relevant front wheel 44Wheels and tyres.
- Unclip brake hose from retainer on wheel bearing housing.
- Unclip pad wear indicator wire.
- Remove bolts (1). [Note: To make it easier to detach the brake caliper from the brake disc, use pliers to press the brake pads back slightly. To avoid damaging the caliper, insert a piece of rubber (2) or similar. Take care not to damage the pad wear indicator wire.]
- Carefully detach brake caliper with brake pads installed. [Note: Brake caliper must not be dismantled. Do not loosen any bolts on the brake caliper.] [Note: Use new bolts Electronic parts catalogue.Use only methylated spirits or commercially available brake cleaner to clean the brake caliper housing.]
- ⚠ Do not leave the brake caliper with brake carrier hanging from the brake hose. Take care that brake hose is not damaged by weight of brake components.The brake hose must be renewed if it is damaged.Do not apply brake when brake caliper is removed. — Clean brake caliper.
- Carefully press brake caliper and brake carrier (with brake pads fitted) over brake disc.
- Secure brake caliper using new bolts.
- Clip brake hose into retainer on wheel bearing housing.
- Clip in pad wear indicator wire.
- Fit wheels 44Wheels and tyres.
- Check brake fluid level and top up if necessary.
🎬 Related video tutorial
Independent AUTODOC tutorial for the same job, filmed on a different model (A6 C5 Avant) — the technique carries over, the fasteners and figures on this page are the ones for your car.
How to change front brake caliper on AUDI A6 C5 Avant
Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- Replacing sealing ring final drive/gearbox housing
- Removing and installing head airbag - Saloon
- Removing and installing dash panel with cross member
- Testing signals from/to automatic gearbox
- Checking valve 1 for camshaft timing control – Audi 1.8 ADR
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.