Poly V-belt drive for power steering pump, alternator and air conditioner - exploded view of components — AUDI
Poly V-belt drive for power steering pump, alternator and air conditioner - exploded view of components on Audi: factory workshop procedure for engines.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
🔧 Engine codes this applies to
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
Poly V-belt drive for power steering pump, alternator and air conditioner - exploded view of components
Poly V-belt
Before removing, mark direction of rotation with chalk or felt-tipped pen. If the belt runs in the opposite direction when it is refitted, this can cause breakage.
Removing and installing
Chapter
Check for wear
20 Nm
Alternator
Removing and installing
Electrical system
Rep. Gr.
27
100 Nm + 90° (
1
/
4
turn) further
Renew
Use
counterhold
T10069
to loosen and tighten
20 Nm
Washer
9 Nm
Pulley for coolant pump
Idler roller (top) for poly V-belt
Vibration damper
With pulley for poly V-belt
Removing and installing
Chapter
20 Nm
Washer
20 Nm
Tensioning roller for poly V-belt
Lever for tensioning roller
20 Nm
Tensioning spring
With hydraulic damper
Dowel sleeve
2 x
Check for correct seating in bracket
Bracket
for AC compressor and tensioner
The bracket for AC compressor and tensioner is paired with the bracket for idler roller
Air conditioning system
Rep. Gr.
87
When installing check dowel sleeves
Item
After replacing, check alignment of pulleys on power steering pump and air conditioner compressor
Chapter
40 Nm
Dowel sleeve
2 x
Bracket for power steering pump
When installing check dowel sleeves
Item
After replacing, check alignment of pulleys on power steering pump and air conditioner compressor
Chapter
M8 -20 Nm-; M10 -40 Nm-
20 Nm
Bracket for idler roller
The bracket for AC compressor and tensioner is paired with the bracket for idler roller
Air conditioning system
Rep. Gr.
87
20 Nm
Power steering pump
Removing and installing
Running gear, front-wheel drive and four-wheel drive
Rep. Gr.
48
After replacing, check alignment of pulleys on power steering pump and air conditioner compressor
Chapter
20 Nm
Shim
Different thicknesses
Check alignment of pulleys on power steering pump and air conditioner compressor after renewing power steering pump, air conditioner compressor, bracket for power steering pump or bracket for air conditioner compressor
Chapter
Pulley for power steering pump
20 Nm
25 Nm
Air conditioner compressor
When installing check dowel sleeves
Item
Dowel sleeves
2 x
Idler roller (bottom) for poly V-belt
Washer
20 Nm
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other AUDI procedures
- Checking output stages for ignition coils
- Checking power supply relay for Motronic system -J271
- Removing and installing upper section of intake manifold
- Checking lambda probe heating for primary catalytic converter lambda probes (cylinders 1 to 6)
- Checking solenoid valve 1 for activated charcoal filter -N80 (fuel tank breather valve)
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.