Exploded view - poly V-belt drive with power steering pump — AUDI
Exploded view - poly V-belt drive with power steering pump on Audi: factory workshop procedure for engines CGLC, CGLD, CJCA, CJCB.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
Exploded view - poly V-belt drive with power steering pump
Poly V-belt
Check for wear
Before removing, mark direction of rotation with chalk or felt-tip pen. If the belt runs in the opposite direction when it is refitted, this can cause breakage.
Removing and installing
Chapter
When installing, make sure it is properly seated on pulleys.
Vibration damper
Can only be installed in one position
Removing and installing
Chapter
Cap
For vibration damper
Bolt
Renew
10 Nm + 90°
Bolt
22 Nm
Poly V-belt pulley
For power steering pump
Tensioner
For poly V-belt
Use
locking tool
T40098
to lock tensioner.
Removing and installing
Chapter
Bracket
For ancillaries
Removing and installing
Chapter
Bolt
Tightening torque
Electrical system
Rep. gr.
27
Alternator; Exploded view - alternator
Alternator
Removing and installing
Electrical system
Rep. gr.
27
Alternator; Removing and installing alternator
Bolt
20 Nm + turn 180° further
Power steering pump
Removing and installing
Running gear, axles, steering
Rep. gr.
48
Hydraulic power steering; Removing and installing power steering pump
Bolt
Renew
Tightening torque and sequence
Fig.
Dowel sleeve
Ensure correct seating in bracket
Air conditioner compressor
Do not unscrew or disconnect refrigerant hoses or pipes.
Removing and installing
Heating, air conditioning
Rep. gr.
87
Air conditioner compressor; Detaching and attaching air conditioner compressor at bracket
Pay attention to dowel sleeves
Item
when installing
Bolt
Tightening torque
Heating, air conditioning
Rep. gr.
87
Air conditioner compressor; Exploded view - air conditioner compressor drive unit
Bolt
Tightening torque
Running gear, axles, steering
Rep. gr.
48
Hydraulic power steering; Removing and installing power steering pump
Idler roller
For poly V-belt
With cover cap
Note installation position
Bolt
Renew
20 Nm + 90°
Bracket for ancillaries - tightening torque and tightening sequence
Note
Renew the bolts tightened with specified tightening angle.
Fit bolts in the following sequence:
Bolts
1, 5, 6
M10x60.
Bolt
2
M10x40.
Bolts
3, 4
M10x155.
Tighten bolts in 5 stages in the sequence shown:
Stage
Bolts
Tightening torque/angle specification
1.
1 … 6
Screw in by hand until contact is made
2.
1 … 6
40 Nm
3.
1
and
2
Turn 60° further
4.
3
and
4
Turn 180° further
5.
5
and
6
Turn 60° further
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →🎬 Video walkthrough
Independent video tutorial by AUTODOC (YouTube) — a helpful visual companion to the steps above.
How to change serpentine belt / v-ribbed belt on AUDI A4 B8 Saloon
Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- Removing and installing seat cover and padding
- Checking fluid level in hydraulic pump – Audi A3 · 1 torque figures
- Testing the system – Audi A6 C5
- Removing and installing charge air cooler (left-side) – Audi
- Removing and installing intake manifold (left and right bottom sections) - vehicles up to 10.2004
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.