Exploded view of front brake FS 3 — AUDI
Exploded view of front brake FS 3 on Audi: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
General information => Page
46-1
Cross-head bolt, 4 Nm
Brake disc
Assignment, dimensions, wear limit => Page
00-1
onwards
Removal involves unscrewing brake caliper
Do not force brake discs off wheel hub; use rust remover if necessary to avoid damaging brake discs
Always replace on an axle basis
Brake pad
Pad thickness, wear limit=>Page 00-4
Different versions
=> Parts List
Checking pad thickness
=> Maintenance
Removing and installing=>Page
46-7
Heed installation position => Fig.
1
Always replace on an axle basis
Brake caliper
Piston diameter => Page 00-4
Removing and installing=>Page
46-11
Servicing => Page
47-4
Guide pin, 28 Nm
Cap
Brake hose with banjo union and banjo bolt, 35 Nm
Locating pin => Fig.
2
Wheel bearing housing
Hexagon socket-head bolt
Tightening torque => Page
45-37
Speed sensor
Removing and installing=>Page
45-39
Splash plate
Bolt, 10 Nm
Wheel bearing
Removing and installing
=> Running Gear, Front-wheel Drive and Four-wheel Drive; Repair Group 40; Wheel bearing housing
Running Gear, Front-wheel Drive and Four-wheel Drive
Wheel bearing housing
Circlip
Wheel hub with rotor
Removing and installing
=> Running Gear, Front-wheel Drive and Four-wheel Drive; Repair Group 40; Wheel bearing housing
Running Gear, Front-wheel Drive and Four-wheel Drive
Wheel bearing housing
Brake pad
With wear indicator (left side only)
Warning lamp in dash panel insert lights on reaching wear limit
Pad thickness, wear limit=>Page 00-4
Different versions
=> Parts List
Checking pad thickness
=> Maintenance
Removing and installing=>Page
46-7
Heed installation position => Fig.
1
Always replace on an axle basis
Connector
Take out of holder -item
18
- on replacing pad
Holder
Self-tapping screw
Fig.1
Installation position of brake pads
Pad with large three-prong clip -1- facing piston end
Pad with small three-prong clip -2- (black colour) facing outside of brake caliper
Fig.2
Brake hose connection with locating pin
Make sure groove in banjo union of brake hose is inserted in locating lug -arrow-.
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- 5-speed manual gearbox 02T — Dismantling and assembling differential
- Removing and installing voltage regulators – Audi A2 · 1 torque figures
- Renewing oil seal for inlet camshaft sprocket with camshaft adjuster
- Removing and installing selector lever lock solenoid N110 on vehicles with vehicle ID No. from 8E_8A 002700 onwards
- Checking knock sensors – Audi TT Mk1
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.