Exploded view - gearbox with hydraulic control Type E17 — AUDI
Exploded view - gearbox with hydraulic control Type E17 on Audi: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
Exploded view - gearbox with hydraulic control Type E17
ATF drain plug, 40 Nm
Hexagon socket, 5 mm
Seal
Renew
Bolt, 10 Nm
Tighten in stages and in diagonal sequence
Oil pan
Removing and installing
Chapter
Gasket
Renew
ATF strainer
Removing and installing
Chapter
Bolt, 8 Nm
For securing valve body
M6 x 30 mm (1x)
M6 x 60 mm (16x)
Follow correct tightening sequence
Servicing automatic gearbox 01V, front-wheel drive and four-wheel drive
Rep. Gr.
38
Valve body
Removing and installing
Servicing automatic gearbox 01V, front-wheel drive and four-wheel drive
Rep. Gr.
38
Select correct version according to gearbox code letters
Electronic parts catalogue
Bolt, 8 Nm
Bracket
For wiring harness
Engage wiring harness on bracket
Bolt, 6 Nm
Gearbox speed sender
G38
Removing and installing
Servicing automatic gearbox 01V, front-wheel drive and four-wheel drive
Rep. Gr.
38
Spacer sleeve
Length: 8 mm
Internal oil pipe
Renew
Removing and installing
Servicing automatic gearbox 01V, front-wheel drive and four-wheel drive
Rep. Gr.
38
O-ring
Renew
Speedometer sender
G22
Removing and installing
Chapter
O-ring
Renew
Lubricate with ATF when installing
Multi-function switch
F125
Removing and installing
Chapter
Renewing oil seal for selector shaft
Chapter
Bolt, 8 Nm
O-ring
Renew
Retaining clip
Wiring harness in gearbox
Gearbox oil temperature sender
G93
integrated in wiring harness
Removing and installing
Servicing automatic gearbox 01V, front-wheel drive and four-wheel drive
Rep. Gr.
38
Disengage from bracket
Item
Position of wiring harness connector: flat part of rear collar faces towards oil pan; lugs on collar are horizontal
Bolt, 6 Nm
Gearbox input speed sender
G182
Removing and installing
Servicing automatic gearbox 01V, front-wheel drive and four-wheel drive
Rep. Gr.
38
Spacer sleeve
Length: 20 mm
Bolt, 6 Nm
Bracket
For solenoid valve
Solenoid valve 4
N91
With O-ring
Removing and installing
Servicing automatic gearbox 01V, front-wheel drive and four-wheel drive
Rep. Gr.
38
Removing and installing valve body
Solenoid valve 3
N90
Without O-ring
Removing and installing
Chapter
“
Removing and installing oil pan
”
Solenoid valve 2
N89
Without O-ring
Removing and installing
Chapter
“
Removing and installing oil pan
”
Bolt, 6 Nm
Bracket
For solenoid valves
Solenoid valve 6
N93
With O-ring
Removing and installing
Chapter
“
Removing and installing oil pan
”
Solenoid valve 7
N94
With O-ring
Removing and installing
Chapter
“
Removing and installing oil pan
”
Solenoid valve 5
N92
With O-ring
Removing and installing
Chapter
“
Removing and installing oil pan
”
Solenoid valve 1
N88
Without O-ring
Removing and installing
Chapter
“
Removing and installing oil pan
”
and detach guide plate for parking lock mechanism
When installing, do not tighten bolts for guide plate (23 Nm) with selector lever in
“P”
Bolt, 6 Nm
Magnet
4 x, in recesses in oil pan
O-ring
Renew
ATF inspection plug, 80 Nm
Hexagon socket, 17 mm
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- Dismantling and assembling 1st - 3rd gear clutch -K1- with turbine shaft for gearboxes up to 11.92
- Checking accelerator position sender G79 - vehicles with 6-cylinder engine
- Removing and installing fuel delivery unit (vehicles with front-wheel drive)
- Removing and installing fuel delivery unit (vehicles with four-wheel drive)
- Renewing oil seal for propshaft flange on rear final drive (rear final drive installed)
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.