Exploded view - clutch housing — AUDI
Exploded view - clutch housing on Audi: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
📋 Procedure
Audi
Audi A3
2004
Power transmission
6-speed manual gearbox 02Q, four-wheel drive
Edition
10.2009
Exploded view - clutch housing
Bearing bush for selector rods
Pulling out
Fig.
Driving in
Fig.
Reverse gear selector fork shaft
Installed up to gearbox manufacturing date 24 05 9
Fig.
Shaft cannot be removed with workshop tools
Up to gearbox manufacturing date 24 05 9: press in new shaft if a new clutch housing is fitted
Fig.
Discontinued from gearbox manufacturing date 25 05 9 onwards; reverse gear selector fork is then mounted together with selector fork for 5th/6th gear
Fig.
For correct version, refer to
Electronic parts catalogue
Reverse shaft needle bearing
Always renew after removing
Pulling out
Fig.
Pressing in
Fig.
Dowel sleeve
2x
Clutch housing
If renewed: Adjust output shafts and differential
Chapter
Input shaft oil seal
Renewing
Chapter
Can be removed using
sleeve
30 - 21
when gearbox is dismantled
Oil seal
Between gearbox and bevel box
Renewing with manual gearbox installed
Chapter
Use
oil seal extractor lever
VW 681
or
pulling hook
T20143/2
to pull out.
When gearbox has been dismantled, it can be driven in onto stop using
thrust piece
T40007
.
Shim
For differential
Installation position: Shoulder on inside diameter faces towards oil seal
Item
Tapered roller bearing outer race
For differential
Removing and installing
Chapter
If renewed: adjust differential
Chapter
Oil deflector plate
Installation position: Shoulder on drilling faces towards output shaft
Tapered roller bearing outer race
For 1st - 4th gear output shaft
Removing and installing
Chapter
If renewed: Adjust 1st - 4th gear output shaft
Chapter
Tapered roller bearing outer race
For 5th/6th and reverse gear output shaft
Removing and installing
Chapter
If renewed: Adjust 5th/6th and reverse gear output shaft
Chapter
Shim
For 5th/6th and reverse gear output shaft
0.65 mm thick
Roller bearing
For input shaft
Removing and installing
Chapter
Magnet
Held in place by joint surface of housing
Cap
Only fitted in clutch housing for 4-cylinder engine
Reverse gear selector fork shaft in gearboxes manufactured up to 24 05 9
Fit reverse gear selector fork
1
on shaft
2
behind selector rod for 5th/6th gear
3
.
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- Checking delivery pressure of fuel system pressurisation pump G6
- Renewing gasket between bi-turbo turbine housings – Audi CFCA
- Removing and installing propshaft flange seal, up to model year 2010
- Removing and installing actuator for differential lock
- Removing and installing intermediate bearing
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.