Electric/electronic gearbox components — AUDI
Electric/electronic gearbox components on Audi: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
📋 Procedure
Electric/electronic gearbox components
Clutch travel sender
G162
Fitting location: on the clutch slave cylinder
Can be checked electrically
Chapter
and via reading measured value block
Chapter
Removing and installing
5-speed Manual Gearbox 085 DS
Rep. Gr.
30
Gearbox speed sender
G38
Fitting location: at top of gearbox housing
Can be checked electrically
Chapter
and via reading measured value block
Chapter
Removing and installing
5-speed Manual Gearbox 085 DS
Rep. Gr.
30
Potentiometer 2 for gear recognition
G240
Recognises the gate (similar to
“gear stick to left/right”
)
Fitting location
Fig.
Can be checked via reading measured value block
Chapter
Removing and installing
5-speed Manual Gearbox 085 DS
Rep. Gr.
34
Potentiometer 1 for gear recognition
G239
Recognises the gear position (similar to
“gear stick to front/rear”
)
Fitting location
Fig.
Can be checked via reading measured value block
Chapter
Removing and installing
5-speed Manual Gearbox 085 DS
Rep. Gr.
34
Gear selector valve 1
N284
For gear selection
Fitting location
Fig.
Can be checked electrically
Chapter
and via reading measured value block
Chapter
Removing and installing
5-speed Manual Gearbox 085 DS
Rep. Gr.
34
Gear selector valve 4
N287
For gate selection
Fitting location
Fig.
Can be checked via reading measured value block
Chapter
Removing and installing
5-speed Manual Gearbox 085 DS
Rep. Gr.
34
Gear selector valve 3
N286
For gate selection
Fitting location
Fig.
Can be checked electrically
Chapter
and via reading measured value block
Chapter
Removing and installing
5-speed Manual Gearbox 085 DS
Rep. Gr.
34
Gear selector valve 2
N285
For gear selection
Fitting location
Fig.
Can be checked via reading measured value block
Chapter
Removing and installing
5-speed Manual Gearbox 085 DS
Rep. Gr.
34
Fitting location for potentiometer for gear recognition at gear actuator
Note the different lengths of the wiring:
Potentiometer 1 for gear recognition
G239
; long wire.
Potentiometer 2 for gear recognition
G240
; short wire.
The
arrows
indicate the attachment of the wiring harness on the gear actuator.
Fitting location of valves 1 to 4 for gear selection
Please note different electrical connectors for gear selector valves.
Gear selector valve 1
N284
; large connector, no colour marking
Gear selector valve 2
N285
; large connector, colour marking
arrows A
Gear selector valve 3
N286
; small connector, no colour marking
Gear selector valve 4
N287
; small connector, colour marking
arrows B
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- Checking low pressure on high-pressure pump, engines with supplementary fuel pump V393
- Removing and installing front passenger side airbag unit with igniter
- Separating cover and padding, double cab
- Removing and installing sliding door remote release mechanism
- Removing undamaged sliding window for side panel
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.