FORD CYFB — 2.2L Engine
2.2L · 125 hp
Engine overview
Vehicles with this engine
Torque figures by job
From the step-by-step procedures for this engine — each figure sits in the step that uses it.
- 20 Nm (15 lb-ft) — Use bolt (1) to fix engine support T10359 with
- 20 Nm (15 lb-ft) — Use bolt (1) to fix engine support T10359 with
- 20 Nm (15 lb-ft) — ⚠ Risk of damage to valves and piston crowns
- 5 Nm (3.7 lb-ft) — If injector does not come loose after limit torque of
- 5 Nm (3.7 lb-ft) — If injector does not come loose after limit torque of
- 8 Nm (5.9 lb-ft) — Tighten bolts to
- 8 Nm (5.9 lb-ft) — 1
- 8 Nm (5.9 lb-ft) — Tighten bolts to
- 8 Nm (5.9 lb-ft) — 1
- 5 Nm (3.7 lb-ft) — If torque limit of »
- 13 Nm (9.6 lb-ft) — Tighten adjusting screw (arrow) to
- 40 Nm (30 lb-ft) — Tighten with torque wrench initially to
- 4 Nm (3.0 lb-ft) — Pre-tighten bolts (arrows) to
Engine codes in the same family
The same code prefix usually means the same block with a different output, fuel or model year. Procedures are often shared — check the code on the engine plate.
Workshop procedures for this engine
Step-by-step procedures from the workshop database, carrying 51 torque figures.
- Installing gearbox · 8 torque figures
- Adjusting differential – VW Sharan I / SEAT Alhambra · 10 torque figures
- Removing gearbox · 5 torque figures
- Installing bevel box – VW Golf V / Jetta · 7 torque figures
- Checking and adjusting selector lever cable – VW 2.0 · 5 torque figures
- Removing and installing coolant shut-off valve N82 – Audi 2.0 · 5 torque figures
- Removing and installing camshaft timing chain - vehicles with engine codes CJSA, CJSB, CJXB, CJXC, CJXF, CYFB
- Removing and installing camshaft timing chain - vehicles with engine codes CNSB, CNTC, CHHB
- Removing and installing camshaft - vehicles with engine codes CJSA, CJSB (up to 01.07.2013)
- Removing and installing camshaft - vehicles with engine codes CJSA, CJSB (from 01.07.2013 onwards), CJXB, CJXC, CJXF, CYFB
- Removing and installing camshaft - vehicles with engine codes CNSB, CNTC, CHHB
- Dismantling and assembling gearbox
- Removing and installing camshaft, version A – VW
- Removing and installing camshaft, version B – VW
- Removing and installing mechatronic unit – VW Jetta VI
- Removing bevel box · 1 torque figures
- Removing and installing selector mechanism – VW 2.0
- Removing and installing fuel tank - vehicles with high-voltage system
- Removing and installing timing chain cover (bottom) – VW · 1 torque figures
- Removing and installing mounting bracket – VW 2.0 · 1 torque figures
- Removing and installing injectors, FSI engines – Audi A3 · 2 torque figures
- Removing gearbox, all-wheel drive – VW
- Checking fuel system pressurisation pump G6 - vehicles with 4-cyl. engine
- Renewing oil seal for right flange shaft, four-wheel drive · 2 torque figures
- Assembly overview - valve gear · 4 torque figures
Got a CYFB problem? Ask for free.
Describe the symptoms — TorqFix replies with a diagnosis cited from verified workshop data.
Get free diagnosis →Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 14 Oct 2026.