Removing dual clutch, gearboxes made up to 05.2011 — VW

🧭 Before you start

Fits: VW Passat CC (357, 2008–2012), VW Polo 6R (2009–2014), VW Touran I (1T, 2003–2015), VW Golf V / Jetta (1K, 2003–2009), VW Passat B6 (3C, 2005–2010), VW Golf VI (5K, 2008–2013); platform codes 5M1, 1F7, 137, 521

• Opens: power steering fluid
• Special tools named: T10356/5
• Renewed: mechatronic unit, retaining ring

Don't miss

• The clutch is pulled off upwards. The mechatronic unit remains on the gearbox.
• Bolts (A), secure with nut as required.
• Risk of damage to clutch and other components!Push down clutch using only very light force. — To press down, turn spindle against thrust piece T10376.
• Only a few, »older« gearboxes do not have a clip.

📋 Procedure

1. Pull off both breather caps (arrows) and close using clean plugs from engine bung setVAS 6122 to achieve an oil-tight seal.
2. ⚠ For some gearboxes the breather cap on the mechatronic unit is destroyed during removal and must be renewed.It is not possible to check the fill level of the hydraulic fluid section of the mechatronic unit. Before repairs, the breather of the mechatronic unit must be sealed so that no oil can escape.Oil which escapes from the hydraulic fluid section of the mechatronic unit cannot be replenished, nor can the oil level be checked. If there is any oil leakage, renew mechatronic unit. — Turn gearbox on engine and gearbox jack upwards together with clutch. [Note: The clutch is pulled off upwards. The mechatronic unit remains on the gearbox.]
3. Remove retaining ring of hub (arrow).
4. Remove hub with hook3438 and a screwdriver.
5. Remove retaining ring (arrow) for clutch. [Note: If the retaining ring cannot be removed it is because the clutch has »clamped« the retaining ring at the bottom.In this case, push the clutch down slightly (see following description) and release the load on the retaining ring. Never strike the clutch or shaft with a hammer!Always renew retaining ring.]

6. Position support bracket T10323 parallel to gearbox flange as shown in illustration.
7. If necessary, balance out gaps using T10356/5, for example.
8. Screw in bolts (A) hand-tight. [Note: Bolts (A), secure with nut as required.]
9. ⚠ Risk of damage to clutch and other components!Push down clutch using only very light force. — To press down, turn spindle against thrust piece T10376.
10. Remove retaining ring (arrow) for clutch.
11. Insert puller T10373 into clutch and bore out clutch.
12. Remove clutch together with puller T10373.
13. Remove small engagement bearing.
14. Remove large engaging lever.
15. Undo bolts and remove small engaging lever. [Note: Only a few, »older« gearboxes do not have a clip.]
16. Remove retainer for engaging lever.

Other VW procedures

• Removing engine · 41 torque figures
• Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
• Adjusting valve timing – VW Passat B5 · 83 torque figures
• Removing and installing camshafts – VW Passat B6 · 39 torque figures
• Removing and installing coolant pump · 53 torque figures
• VW Assemble the planetary gear clutch replacement · 1 torque figures
• VW 2.3 AZX injector removal & installation · 1 torque figures
• VW 2.3 AZX injector removal & installation · 1 torque figures
• Door - remove and install · 6 torque figures
• Transmission (UGA and UKA engines) - remove and install · 5 torque figures