Removing and installing propshaft, Golf 2013 ►, Golf Estate 2014 ► — VW

🧭 Before you start

Fits: VW Golf VII (5G, 2012–2020), VW Golf VII Variant (BA)

Don't miss

• Loosen, but do not remove, propshaft from bevel box at front and from final drive at rear.
• Counterhold at rear final drive when loosening or tightening propshaft.
• Before removal, check if there are coloured marks on flexible coupling and on flange of rear final drive (arrows). If not, mark positions of flexible coupling and propshaft flange of final drive relative to each other (arrows).
• Also mark position of propshaft relative to bevel box flange.
• When pulling off or pushing on propshaft, always ensure that sleeve (arrow) is not damaged.

📋 Procedure

1. Remove noise insulation General body repairs, exterior 66. Noise insulation; Assembly overview - noise insulation.
2. Remove exhaust system 26Exhaust pipes/silencers; Assembly overview - silencer.
3. Unscrew bolts (1) and (2) of pendulum support.
4. Press »engine and gearbox« forwards and secure in position with an appropriate piece of wood (A).
5. Unscrew bolts (A) and (B) from bevel box and remove heat shield (1).

6. Remove heat shield for centre tunnel beneath centre propshaft bearing General body repairs, exterior 66. Underbody cladding; Assembly overview - underbody cladding.
7. Remove rear tunnel cross member General body repairs, exterior 66. Underbody cladding; Assembly overview - underbody cladding.
8. Loosen, but do not remove, propshaft from bevel box at front and from final drive at rear.
9. Counterhold at rear final drive when loosening or tightening propshaft.
10. Before removal, check if there are coloured marks on flexible coupling and on flange of rear final drive (arrows). If not, mark positions of flexible coupling and propshaft flange of final drive relative to each other (arrows).
11. Also mark position of propshaft relative to bevel box flange.
12. Unscrew propshaft bolts from bevel box at front and from rear final drive (arrows). [Note: Now, the propshaft is held in position solely by the centring pins on bevel box and final drive as well as by the centre propshaft bearing in the middle. From now on a second mechanic is required for the further removal of the propshaft.]
13. While a second mechanic is holding the propshaft in installation position, remove centre propshaft bearing (arrows) and remove propshaft towards rear with the joint as straight as possible.
14. When pulling off or pushing on propshaft, always ensure that sleeve (arrow) is not damaged.
15. ⚠ To avoid damaging the protective boot in the centre propshaft bearing, remove, store and install the propshaft with the joint as straight as possible. — Install all parts which were marked in relation to each other in their original positions.
16. Align centre propshaft bearing in its elongated holes so that neither propshaft nor centre propshaft bearing is under tension.
17. Do not tighten centre propshaft bearing until propshaft has been fitted.
18. Tighten bolts for propshaft and centre propshaft bearing. Specified torques (value given in the factory table, not available here).
19. Bolt heat shield (1) on bevel box.
20. Bolt on pendulum support using »new« bolts. Specified torques: Running gear, axles, steering 40. Subframe; Assembly overview - subframe.
21. Install heat shield for centre tunnel beneath centre propshaft bearing General body repairs, exterior 66. Underbody cladding; Assembly overview - underbody cladding.
22. Install exhaust system 26Exhaust pipes/silencers; Assembly overview - silencer.
23. Install rear tunnel cross member General body repairs, exterior 66. Underbody cladding; Assembly overview - underbody cladding.
24. Install noise insulation General body repairs, exterior 66. Noise insulation; Assembly overview - noise insulation.

Other VW procedures

• Removing engine · 41 torque figures
• Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
• Adjusting valve timing – VW Passat B5 · 83 torque figures
• Removing and installing camshafts – VW Passat B6 · 39 torque figures
• Removing and installing coolant pump · 53 torque figures
• Removing and installing air recirculation flap control motor V113, vehicles without air flow flap control motor V71
• Renewing components
• Specified values for wheel alignment, multi-link suspension, Golf
• Checking fuel system pressurisation pump G6
• Removing and installing refrigerant expansion valve 1 N636