Removing and installing front 3-point seat belt, 2-door model — VW
Removing and installing front 3-point seat belt, 2-door model on VW: 15 steps, 2 torque figures. What to remove, what to tighten and to how many Nm, what.
Workshop procedure for VW — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
Fits: platform codes 121, BL1
Don't miss
- Ensure that no electric cables are laid in the area of the belt reel! — Switch on ignition.
🔩 Torque settings
Values can differ between engine variants — check the code stamped on your block.
| Torque | Fastener / step |
|---|---|
| 40 Nm (30 lb-ft) | Open cap (1)(arrow) and unscrew bolt (3 |
| 40 Nm (30 lb-ft) | Undo bolt (1 |
ℹ️ Always cross-check the exact figure against your vehicle's factory manual before final tightening — a wrong torque can damage the engine. These values are extracted from workshop data and may not cover every variant or revision.
📋 Procedure
- ⚠ Follow safety regulations for pyrotechnic components .Follow disposal regulations for pyrotechnic components . — Disconnect battery earth cable with ignition switched on Electrical system27Battery; Connecting and disconnecting battery.
- Remove bench seat .
- Remove rear seat backrest .
- Remove side trim .
- Unclip front sill panel moulding in vicinity of belt inertia reel .
- Open cap (1)(arrow) and unscrew bolt (3) (40 Nm). — 40 Nm (30 lb-ft)
- Remove belt guide fitting (2) with belt webbing.
- Unclip C-pillar trim where it overlaps with B-pillar trim.
- Remove B-pillar trim, 2-door model .
- Remove front belt guide .
- Remove front seat belt end anchor .
- Undo bolt (1) (40 Nm) and remove belt inertia reel (2) from mounting. — 40 Nm (30 lb-ft)
- Install in reverse order of removal.
- ⚠ Ensure that no electric cables are laid in the area of the belt reel! — Switch on ignition.
- ⚠ Battery must be connected with ignition switched on. If pyrotechnic components (e.g. airbag, seat belt tensioners) are repaired incorrectly, undesired triggering may occur after the battery is connected. Ensure that nobody is in vehicle when connecting battery. — Connect battery earth cable with ignition switched on Electrical system27Battery; Connecting and disconnecting battery.
Other VW procedures
- Removing engine · 41 torque figures
- Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
- Adjusting valve timing – VW Passat B5 · 83 torque figures
- Removing and installing camshafts – VW Passat B6 · 39 torque figures
- Removing and installing coolant pump · 53 torque figures
- Removing and installing vacuum unit for charge pressure regulating valve · 1 torque figures
- Assembling output shaft 2
- Checking fuel delivery rate (engine codes CAWA, CAWB, CBFA, CCTA, CCTB, CGYA, BZB)
- Removing and installing thermostat housing – VW Jetta VI
- Removing and installing fuel delivery unit, fuel gauge sender and suction-jet pumps · 1 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.