Removing and installing door trim at front — VW
Removing and installing door trim at front on VW: 17 steps, 11 torque figures. What to remove, what to tighten and to how many Nm, what to check after.
Workshop procedure for VW — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
Fits: platform code 138
- Renewed: as necessary
Don't miss
- Before installing door trim, ensure that the locking mechanisms of all clips are in (position 1).It is not possible to install the door trim without problem if clips are in (position 2). — Connect connectors to door trim panel.
- Ensure retaining tab (1) is properly engaged.
- To prevent the securing clips from canting when fitting the door trim to the door, always guide trim onto inner panel at an angle ≥ 20° "“angle α”". — Press door trim panel into corresponding openings in inner door panel.
🔩 Torque settings
Values can differ between engine variants — check the code stamped on your block.
| Torque | Fastener / step |
|---|---|
| 1.7 Nm (1.3 lb-ft) | Unscrew bolt (1 |
| 1.7 Nm (1.3 lb-ft) | Unscrew bolts (1 |
| 2 Nm (1.5 lb-ft) | Remove bolt (1 |
| 2 Nm (1.5 lb-ft) | Unscrew 2 bolts (arrows |
| 4.5 Nm (3.3 lb-ft) | Remove bolt (1) on underside |
| 4.5 Nm (3.3 lb-ft) | Remove screw (1 |
| 4.5 Nm (3.3 lb-ft) | Tighten screw (2 |
| 4.5 Nm (3.3 lb-ft) | Unclip caps (2) using removal wedge3409 and unscrew bolts (1 |
| 4.5 Nm (3.3 lb-ft) | Unscrew 4 bolts (arrows |
| 4.5 Nm (3.3 lb-ft) | Unscrew bolts (1) and (2 |
| 4.5 Nm (3.3 lb-ft) | Unscrew bolts (3) and (4 |
ℹ️ Always cross-check the exact figure against your vehicle's factory manual before final tightening — a wrong torque can damage the engine. These values are extracted from workshop data and may not cover every variant or revision.
📋 Procedure
- Switch off ignition.
- Using removal wedge3409, carefully unclip trim (1).
- Unscrew bolts (arrows).
- Remove bolts (1).
- ⚠ When the door trim is separated, there is a risk that fastening elements may be damaged. To avoid this, always follow the specified order and positions of clips when removing the door trim. — Release door trim from clips in (specified sequence) using wedges T10383.
- Pull door trim upwards vertically out of window slot.
- Pull retaining tab (1) on inner side of door trim panel outwards.
- Pull Bowden cable towards back out of guide.
- Unhook Bowden cable (2) from inner door handle.
- Disconnect connectors from door trim panel.
- Check securing clips for damage and renew as necessary.
- ⚠ Before installing door trim, ensure that the locking mechanisms of all clips are in (position 1).It is not possible to install the door trim without problem if clips are in (position 2). — Connect connectors to door trim panel.
- Attach Bowden cable (2) of interior door handle.
- Ensure retaining tab (1) is properly engaged.
- Hook door trim in window slot.
- ⚠ To prevent the securing clips from canting when fitting the door trim to the door, always guide trim onto inner panel at an angle ≥ 20° "“angle α”". — Press door trim panel into corresponding openings in inner door panel.
- Engaged in door trim in cover (1).
Other VW procedures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.