Removing and installing bevel box , Passat 2011 ► with 3.6 l V6 engine — VW
Removing and installing bevel box , Passat 2011 ► with 3.6 l V6 engine on VW: factory workshop procedure for engines BWS, BYD, CBRA, CDLA.
Workshop procedure for VW — the factory write-up, straight from real workshop data.
📐 5 workshop diagrams for BWS
Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
VW
Golf
2004
Golf
2009
Golf Cabriolet
2012
Passat
2006
Passat Variant
2006
Scirocco
2009
Power transmission
6-speed dual clutch gearbox 02E Volkswagen R GmbH
Edition
07.2014
Removing and installing bevel box , Passat 2011 ► with 3.6 l V6 engine
Special tools and workshop equipment required
Tensioning strap
T10038
Socket
T10107 A
Removing:
Raise vehicle. All 4 supports of lifting platform must be at same height.
Move selector lever to position
»P«
position.
Remove noise insulation
General body repairs, exterior
Rep. gr.
66
Removing and installing wheel housing liner; Front wheel housing liner
.
Unbolt right drive shaft from gearbox
Rep. gr.
40
Removing and installing drive shafts
.
Secure drive shaft to suspension strut with
tensioning belt
T10038
.
Remove pendulum support
Rep. gr.
40
Assembly overview - subframe, anti-roll bar, suspension links
Remove exhaust system bracket from subframe
arrows
Rep. gr.
26
Exhaust system
.
Mark position of propshaft with flexible coupling relative to bevel box flange with paint.
Unbolt propshaft from bevel box
arrows
Rep. gr.
39
Removing and installing propshaft
.
Push front propshaft tube to stop.
The
seal
in the propshaft must not be damaged.
Remove heat shield above right drive shaft
1
Rep. gr.
40
Heat shields for drive shafts
.
Remove bracket
A
between engine and bevel box.
First remove bolt
1
.
Remove counter-sunk bolt using
insert
T10107 A
.
Flange shaft remains in bevel box.
Unbolt bevel box from gearbox
arrows
and remove it.
To remove bevel box, push engine forwards slightly (second mechanic).
Installing
Install in reverse order of removal. During this step, observe the following:
Push bevel box together with flange shaft onto gearbox and turn flange shaft while doing so.
Bolt bevel box onto gearbox using 4 new bolts.
Torque setting
40 Nm
Screw in bolts
1
and
2
hand-tight.
Observe assembly order:
First tighten bolts
1
to 3 Nm.
Tighten bolts
2
to 40 Nm.
Finally tighten bolts
1
to 40 Nm.
Install counter-sunk bolt using
insert
T10107 A
.
Torque setting
30 Nm
Install heat shield above right drive shaft
1
Rep. gr.
40
Heat shields for drive shafts
.
Bolt right drive shaft to gearbox
Rep. gr.
40
Removing and installing drive shafts
.
Install pendulum support
Rep. gr.
40
Assembly overview - subframe, anti-roll bar, suspension links
.
Bolt propshaft to bevel box
arrows
Rep. gr.
39
Removing and installing propshaft
.
Bolt exhaust system bracket to subframe
arrows
Rep. gr.
26
Exhaust system
.
Continue installation in reverse order of removal.
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other VW procedures
- Checking gear oil in bevel box · 1 torque figures
- Removing rear final drive 01Z – VW Passat B6
- 6-speed dual clutch gearbox 02E Volkswagen R GmbH — Renewing seal on gearbox selector lever · 1 torque figures
- Removing and installing vibration damper (engine code BWS) · 1 torque figures
- Emptying fuel tank with fuel tank less than 3/4 full, vehicles with front-wheel drive
- Removing engine · 41 torque figures
- Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
- Adjusting valve timing – VW Passat B5 · 83 torque figures
- Removing and installing camshafts – VW Passat B6 · 39 torque figures
- Removing and installing coolant pump · 53 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.