Overview - valve body — VW
Overview - valve body on VW: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for VW — the factory write-up, straight from real workshop data.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
VW
Phaeton
2003
Power transmission
5-speed automatic gearbox 01L, all-wheel drive
Edition
10.2012
Overview - valve body
After reinstalling oil pan, check ATF level and top up
Chapter
.
Dismantling and assembling procedure
Chapter
Drain plug, 12 Nm
Hexagon socket head, 5 mm.
With seal
Always renew
Remove to drain ATF
Chapter
.
Seal
Always renew
Bolt, 10 Nm
Tighten oil pan bolts diagonally in several stages.
Oil pan
Removing and installing
Chapter
Seal
Always renew
ATF strainer
Removing and installing
Chapter
O-ring
Always renew
Moisten with gear oil and insert.
Bolt, 8 Nm
To secure valve body: 5 bolts M6x30, 1 bolt M6x55 (chromatised), 15 bolts M6x60.
Removing and installing
Chapter
Valve body
Removing and installing
Chapter
O-ring
Not present on this vehicle.
Speedometer sender
G22
or
vehicle speed sender
G68
Not present on this vehicle.
Gearbox speed sender
G38
or
gearbox output speed sender
G195
Selector shaft seal
Renewing selector shaft seal
Chapter
.
Lever
For selector shaft
For removal, spring pin must be removed.
Spring pin
Multifunction switch
F125
Renewing
Chapter
Bolt, 8 Nm
Bracket
For wiring harness
Bolt, 5 Nm
Bracket
For solenoid valve
Solenoid valve 3
N90
Without O-ring
Solenoid valve 2
N89
Without O-ring
Solenoid valve 1
N88
Without O-ring
Automatic gearbox pressure control valve 5
N233
With O-ring.
Moisten O-ring with ATF and insert.
Automatic gearbox pressure control valve 2
N216
With O-ring.
Moisten O-ring with ATF and insert.
Automatic gearbox pressure control valve 3
N217
With O-ring.
Moisten O-ring with ATF and insert.
Automatic gearbox pressure control valve 4
N218
With O-ring.
Moisten O-ring with ATF and insert.
Automatic gearbox pressure control valve 1
N215
With O-ring.
Moisten O-ring with ATF and insert.
O-ring
Always renew
Moisten with ATF and insert.
Spacer sleeve
Length: 8.7 mm
Gearbox input speed sender
G182
Bolt, 5 Nm
Wiring harness
Renewing
Chapter
Gearbox oil (ATF) temperature sender
G93
integrated in wiring harness
Bolt, 5 Nm
O-ring
Always renew
Moisten with gear oil and insert.
Retaining ring
Always renew
Magnet
Qty. 4 in depressions in oil pan
Always clean when oil pan is removed
Ensure that magnets are correctly seated in oil pan
O-ring
Always renew
ATF inspection plug
Tightening
Chapter
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other VW procedures
- Removing engine · 41 torque figures
- Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
- Adjusting valve timing – VW Passat B5 · 83 torque figures
- Removing and installing camshafts – VW Passat B6 · 39 torque figures
- Removing and installing coolant pump · 53 torque figures
- Left retaining strip · 4 torque figures
- Balancing wheel, balancing wheel on stationary wheel balancer · 4 torque figures
- StarterB for vehicles with 1.0l, 1.6l and 2.0l engines (ARA, BAH, BPA, CCRA, BBX, CFEA) · 4 torque figures
- Installation position, gear wheel for 3rd gear · 2 torque figures
- Compression - check · 4 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.