Front seat belt ("“4-door”" Gol/Voyage without pre-tensioner) - remove and install — VW
Front seat belt ("“4-door”" Gol/Voyage without pre-tensioner) - remove and install on VW: 16 steps, 3 torque figures.
Workshop procedure for VW — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
- Renewed: self-locking nuts
🔩 Torque settings
Values can differ between engine variants — check the code stamped on your block.
| Torque | Fastener / step |
|---|---|
| 3.5 Nm (2.6 lb-ft) | Install the seat belt clip (12) and tighten the securing bolts (11) |
| 40 Nm (30 lb-ft) | Tighten the securing bolt (3) to the torque |
| 40 Nm (30 lb-ft) | Tighten the securing bolt (7) to the torque |
ℹ️ Always cross-check the exact figure against your vehicle's factory manual before final tightening — a wrong torque can damage the engine. These values are extracted from workshop data and may not cover every variant or revision.
📋 Procedure
- Remove the B-pillar lower lining (see the separate procedure).
- Remove the lower fastening point of seat belt(8).
- Remove belt guide cover (4).
- Remove the securing bolt (3).
- Remove the director (2).
- Remove securing bolts (11) of the seat belt clip (12).
- Remove the securing bolt (7).
- Remove the automatic belt retractor (5) and the noise insulation (6) from B-pillar.
- ⚠ Replace self-locking nuts and bolts subject to angular torque — Install the automatic belt retractor (5) and the noise insulation (6) on B-pillar.
- Tighten the securing bolt (7) to the torque of (40 Nm). — 40 Nm (30 lb-ft)
- Install the seat belt clip (12) and tighten the securing bolts (11) with (3.5 Nm) of torque. — 3.5 Nm (2.6 lb-ft)
- Install the belt guide (2).
- Tighten the securing bolt (3) to the torque of (40 Nm). — 40 Nm (30 lb-ft)
- Install the seat belt guide cover(4).
- Install the lower fastening point of seat belt (8).
- Install B-pillar lower lining (see the separate procedure).
Other VW procedures
- Removing engine · 41 torque figures
- Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
- Adjusting valve timing – VW Passat B5 · 83 torque figures
- Removing and installing camshafts – VW Passat B6 · 39 torque figures
- Removing and installing coolant pump · 53 torque figures
- Main Headlights - remove and install · 3 torque figures
- Voltage regulator C1 (Manufacturer Valeo) - disassemble and assemble · 3 torque figures
- Loosening and tightening twelve point nut securing drive shaft · 3 torque figures
- Loosening and tightening drive shaft hexagon bolt · 3 torque figures
- Deformation elements for dash panel USA · 3 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix → · How these pages are made →Workshop data on this page last updated 20 Sep 2026.