Assembly overview – rear brake, multi-link rear suspension — VW
Assembly overview – rear brake, multi-link rear suspension on VW: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for VW — the factory write-up, straight from real workshop data.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
Assembly overview – rear brake, multi-link rear suspension
Note
Use the
brake filling and bleeding equipment
VAS 5234
to draw off brake fluid from the brake fluid reservoir.
Before removing a brake caliper or disconnecting a brake hose, fit
brake pedal depressor
V.A.G 1869/2
(when doing this, release pressure in system).
After replacing brake pads, depress brake pedal firmly several times with vehicle stationary, so that the brake pads are properly seated in their normal operating position.
Bolt
8 Nm
Bolt
Qty. 2
Renew after removing
90 Nm +90°
Speed sensor
Assembly overview
Chapter
.
Removing and installing
Chapter
Before inserting sensor, clean inner surface of hole and coat with
high-temperature paste
G 052 112 A3
.
Wheel bearing housing
Running gear, axles, steering
Rep. gr.
42
Suspension link wheel bearing; Assembly overview - wheel bearings
Allocation
Electronic Parts Catalogue
Splash plate
Removing and installing
Chapter
Bolt
Qty. 3
12 Nm
Wheel hub with wheel bearing
Running gear, axles, steering
Rep. gr.
42
Suspension link wheel bearing; Assembly overview - wheel bearings
Allocation
Electronic Parts Catalogue
Bolt
Renew every time it is removed.
Running gear, axles, steering
Rep. gr.
42
Suspension link wheel bearing; Assembly overview - wheel bearings
Allocation
Electronic Parts Catalogue
Dust cap
Renew after removing
Running gear, axles, steering
Rep. gr.
42
Suspension link wheel bearing; Assembly overview - wheel bearings
Brake disc
272 mm in diameter
Brake disc thickness: 10 mm
Wear limit: 8 mm.
Checking thickness
Maintenance
Booklet
Front and rear brake discs and pads: Checking condition of discs and thickness of pads
When worn, renew on both sides of axle.
Unscrew brake caliper prior to removing.
Allocation
Electronic Parts Catalogue
Bolt
8 Nm
Brake pads
Thickness without support plate: 11 mm
Wear limit without support plate: 3 mm
Checking thickness
Maintenance
Booklet
Front and rear brake discs and pads: Checking condition of discs and thickness of pads
Always replace on both sides
Removing and installing
Chapter
Brake carrier
Assembly overview
Chapter
.
With guide pins and protective cap.
Deflector cap
Fit onto brake carrier and guide pin.
Guide pin
Grease before fitting protective cap.
Brake caliper
Assembly overview
Chapter
.
Do not unscrew brake line when changing brake pads
Removing and installing
Chapter
Adjust handbrake after repairing or renewing
Adjusting handbrake
Chapter
.
Handbrake cable
Assembly overview
Chapter
.
Adjusting
Chapter
.
Removing and installing
Chapter
Bolt
Qty. 2
Renew after removing
Self-locking
35 Nm
Brake line
With banjo bolt
35 Nm
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other VW procedures
- Removing engine · 41 torque figures
- Removing and installing camshaft – VW Golf Cabriolet · 47 torque figures
- Adjusting valve timing – VW Passat B5 · 83 torque figures
- Removing and installing camshafts – VW Passat B6 · 39 torque figures
- Removing and installing coolant pump · 53 torque figures
- Installing dual clutch, gearbox date from 06.2011
- Checking fuel delivery rate (engine codes CCZA, CCZB, CDAA, CDAB)
- Removing and installing vacuum unit for turbocharger
- Removing and installing fuel tank with attachments and fuel filter
- Removing and installing mounting plate for oil cooler, pressure control valve and oil filter housing · 1 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.